Colorado to New Mexico: general contractor license reciprocity
Colorado does not issue a statewide general contractor license, so there is nothing to transfer. Here is New Mexico's standard path for out-of-state applicants.
Your origin state does not issue a statewide license at this level, so there is no license to transfer. The destination's standard out-of-state path is shown; expect to meet it in full.
Reference only, not legal advice. Rules change; confirm with the licensing board before you apply. Full disclaimer.
GB-98 trade exam waived on the NASCLA Accredited Examination (every state)
Your out-of-state credentials give no advantage. You meet the destination's requirements from scratch.
New Mexico runs no named-state contractor reciprocity: the only reciprocity the Construction Industries Division publishes is for the EE-98J electrical journeyman certificate, and holding another state's general contractor license is worth nothing on its own here. What CID does accept, from an applicant in any state, is the NASCLA Accredited Examination. Under 14.6.3.8(G)(2)(f) NMAC the bureau chief may waive the state-specific written trade exam for a Qualifying Party who passed the NASCLA general construction accredited examination, and CID's own Qualifying Party application limits that waiver to the GB-98 and EE-98 classifications, so at this level a NASCLA pass replaces the two-part GB-98 exam. Three things come with it: the candidate must have used the NASCLA scores to obtain a license in another state and held that license for at least a year, must attach a letter of good standing from that state, and must release the NASCLA transcript to New Mexico from the NASCLA website rather than sending a copy. Nothing else is waived. The four years (8,000 hours) of foreman-level experience, at least two of them commercial, must still be documented on notarized affidavits, the Business and Law exam or approved course still applies, and the company still files the bond, the tax registration certificate and the entity paperwork. An applicant without a NASCLA pass simply sits the GB-98 exam.
The rule says the bureau chief 'may waive' the trade exam, and CID verifies the NASCLA transcript itself after PSI accepts the application and the experience; if CID denies the waiver the applicant is contacted and registered for the full exam sequence, so do not stop studying while the transcript is being checked. The NASCLA waiver is not open at the GB-2 residential level. Out-of-state experience counts in full toward the 8,000 hours where it was gained working for a contractor licensed in the trade or was legal work in the state where it was performed, and an out-of-state contractor signing the affidavit attaches a copy of their current state license; accredited training counts at one-half year per year up to half the requirement, and estimating, project management and supervision do not count as hands-on. Once PSI approves the application, all remaining requirements must be met within six months or the fees are forfeited, exam scores are good for one year, and the trade and Business and Law results must be within a year of each other. NMSA 60-13-14(C) allows the division, with the commission's consent, to enter reciprocal licensing agreements with states having equivalent requirements; no such agreement covering a building classification has been published, so ask the Construction Industries Division before assuming one exists.
At a glance
- Trade exam
- Waived
- Law / code exam
- Required
- Out-of-state hours
- Count toward eligibility
What you must already have
- You must have passed a licensing exam in Colorado that the destination considers comparable.14.6.3.8(G)(2)(f) NMAC lets the bureau chief waive the state-specific written trade exam for a Qualifying Party who passed the NASCLA general construction accredited examination at the passing score, and CID's Qualifying Party application states the waiver is 'Applicable for Qualifying Party's applying for GB98 & EE98 ONLY' and that it 'removes the trade exam requirement ONLY'. The transcript must be released to New Mexico through the NASCLA website; CID verifies it directly. NASCLA is an exam credential rather than a license or an agreement between states, so it is available to a candidate from any state, and it waives no fee, bond, insurance, entity or experience requirement.
- You must have held your Colorado license for at least 1 year.CID's Qualifying Party application requires that the candidate 'must have taken the exam, used scores to obtain a license in another state, and held that license for a minimum of one year'. A NASCLA pass that was never used to obtain a license, or a license held for less than a year, does not support the waiver.
- Your Colorado license must be active and in good standing.
- You must document at least 8,000 hours of qualifying work experience.Four years (8,000 hours) of foreman-level practical or related trade experience within the ten years immediately before application, of which at least two years must be commercial experience (14.6.6.9(B)(2) NMAC; NMSA 60-13-14(B)(8)). It is documented on notarized General Building Work Experience Verification affidavits, one per employer or affiant, completed by an employer, supervisor, foreman or other contractor, and the affidavit must say whether the experience was residential or commercial. The NASCLA waiver does not reduce it.
- Experience must have been gained while employed by a contractor licensed in the trade being applied for, or be work that was legal in the state where it was performed. An out-of-state contractor certifying the experience attaches a copy of their current state license to the affidavit; where that state does not license the trade, proof that the company was active and valid is attached instead.
What you'll do to get licensed in New Mexico
- 1Application fee. Pay the application fee ($30). Non-refundable Qualifying Party application fee, paid to PSI with the notarized application, the work-experience affidavits and, for a NASCLA waiver, the letter of good standing from the licensing state. Complete packets go to the PSI Albuquerque office by hand or mail; faxed and emailed forms are not accepted..
- 2Other. Qualifying Party certificate fee, charged for each classification on the application (14.5.5.14(A) NMAC). With the $30 application fee this is the $36 the Construction Industries Division quotes for a single-classification Qualifying Party filing. ($6).
- 3Trade exam. Pass the destination's trade exam (if applicable). GB-98 General Building Contractor exam, required only where the NASCLA waiver is not used or is not granted. It is a two-part test administered by PSI: Part 1 is the GB-2 Residential Building Contractor paper, 80 questions in 225 minutes, and Part 2 is the commercial paper, 100 questions in 310 minutes, both open book and both needing 75% to pass. Part 2 covers sitework, concrete, masonry, carpentry, metals, roofing, associated trades, general code, plan reading and estimating, and OSHA safety against the 2021 New Mexico Commercial Building Code (14.7.2 NMAC) and the 2021 International Building Code. Both parts must be passed; a candidate who fails one part retakes only that part..
- 4Exam fee. Pay the exam fee ($269.06). PSI fee for the two-part GB-98 exam taken as a combination, which includes the GB-2 paper. A single part costs $134.53 as a retake. A candidate whose NASCLA waiver is approved pays no trade exam fee..
- 5Law / code exam. Pass a law, rules, or code exam. Contractor's Business and Law exam, required of all new Qualifying Party candidates and never waived by the NASCLA route: 50 questions, 130 minutes, open book, 75% (38 points) to pass, covering licensing requirements, estimating and bidding, business organization and financial management, tax and labor law, project management and lien law, contracts, risk management, and environment and safety. An approved Business and Law course taken with a CID-approved vendor may be completed in place of the exam, and an individual who is already an active Qualifying Party does not repeat it when adding a classification..
- 6Exam fee. Pay the exam fee ($68.88). PSI fee for the Business and Law exam..
- 7Contractor license. Hold or obtain a contractor license ($30). Non-refundable contractor license application fee paid to PSI by the business, filed with the notarized Contractor License Application, a copy of the Qualifying Party's certificate or passing score reports, and the Business and Law score or course certificate. A $6 certificate fee covering the license certificate and two wallet cards is charged with it..
- 8License fee. Pay the license or certificate fee ($300). Classification fee for GB-98, covering the full three-year license term on PSI's current schedule. Adding a GS specialty classification alongside it does not raise the total above $300 for the category. Late renewal costs $1 a day for the first 30 days and the equivalent of one year's fee from 30 to 90 days; after 90 days the license is cancelled and the business must reapply..
- 9Surety bond. Post a surety bond ($10,000). $10,000 code bond from a corporate surety authorized to transact business in New Mexico, issued in the exact name shown on the application and effective for the entire three-year license period. It is the statutory proof of responsibility, may be drawn on only to cure division-certified code violations the licensee has not corrected, and must be kept in force for the whole term; claims are limited to two years after final inspection or issuance of a certificate of occupancy. New Mexico sets no net worth, working capital or financial statement test for a contractor license..
- 10Insurance. Carry the required insurance. Workers' compensation coverage is required of every licensed entity, and failure to maintain it is cause for revocation of the license. A sole proprietor with no employees may be exempt; the Workers' Compensation Administration can confirm. An application is placed on hold while the applicant is out of compliance. CID does not require a general liability policy for the license itself, though owners and general contractors normally require one by contract..
- 11Business license. Obtain a business license. A registration certificate issued within the last twelve months by the New Mexico Taxation and Revenue Department in the exact name on the license application, plus proof of registration with the New Mexico Public Regulation Commission for a corporation or LLC, or with the Secretary of State for a limited liability partnership or limited partnership. A corporation, LLC, LP or LLP must be legally authorized to do business in New Mexico before the license issues, the proposed name must be cleared with PSI first, and each member of a joint venture must itself hold a New Mexico license..
- 12Background check. Complete a background check. CID reviews the application against the disqualifying felony convictions listed in 14.6.3.8(F) NMAC and may deny a license or certificate on that basis; sealed, dismissed, expunged or pardoned convictions and juvenile adjudications are not used. An application is also held where there are pending CID disciplinary actions, a workers' compensation compliance problem, a child support delinquency for the proposed Qualifying Party, or an open unlicensed-activity investigation..
Published fees on this path total $667.94, excluding exam-vendor fees, bonds, and insurance.
What you'll need to buy or arrange
Exam preparation
Most boards contract PSI, Prov, or ICC for exams. Check which code edition the exam is written to before buying a prep course.
- Trade exam · if applicable
- Exam fee · $269.06
- Law / code exam
- Exam fee · $68.88
Surety bond
A license or contractor bond is bought from a surety, not the state. Price is a small percentage of the bond amount and depends on your credit.
- Surety bond · $10,000
Liability insurance
Some states require proof of general liability or workers' compensation coverage at licensing time.
- Insurance
Business registration
If you plan to contract in your own name, budget for a business license or entity registration on top of the trade license.
- Business license
How New Mexico licenses general contractors
New Mexico general contractor · “GB-98 General Building Contractor”
Statewide license
New Mexico's unlimited building tier is the GB-98 General Building classification issued by the Construction Industries Division: erect, alter, repair or demolish residential and commercial buildings and certain structures, including everything the GB-2 residential classification and the GF-5, GF-7 and GS specialty classifications cover, plus seal coating and striping of driveways and parking lots. There is no dollar cap on a GB-98 license, but it is a building classification rather than a universal one, so it excludes structures covered by the electrical (EE), mechanical and plumbing (MM), asphalt and concrete (GA) and fixed works (GF) classifications; the separate GA classifications run from GA-1, streets, roads and highways, through GA-98, and a GB-98 contractor may not prime a project whose major portion by dollar value falls in a GA classification or in most GF classifications. The license belongs to a business that employs or is owned by a Qualifying Party, and that individual is the one who documents the experience, passes the exams and holds a personal certificate of qualification. A GB-98 Qualifying Party needs four years (8,000 hours) of foreman-level experience within the last ten years, of which at least two years must be commercial, and must pass the two-part GB-98 exam and the Contractor's Business and Law exam or an approved course in its place. The entity files a $10,000 code bond and carries workers' compensation, and the license runs three years.
Why Colorado has nothing to transfer
Colorado general contractor · “General / Building contractor license (Class A or B in most jurisdictions)”
Licensed by cities and counties
Colorado has no statewide general or commercial building contractor license. DORA licenses electricians and plumbers through its Division of Professions and Occupations but states on its own consumer page that general contractors are not licensed at the state level and that you should check with the city; the Pikes Peak Regional Building Department says the same thing in its exam notice. Unlimited and commercial building work is therefore licensed by each city, county or regional building department, typically as a Class A (unlimited) and Class B (limited commercial or under a height or storey cap) pair: Denver issues General Contractor Class A and Building Contractor Class B, Colorado Springs issues Building Contractor A-1, A-2, B-1 and B-2, Fort Collins issues Classes A, B, C1 and C2, and Aurora issues a single Commercial Building Contractor license. The license is held by the business and qualified by an individual who holds the supervisor certificate and has passed the relevant exam, so the person moving states applies for the certificate and the company applies for the license. The common thread is the ICC National Standard General Building Contractor (A) and Building Contractor (B) examinations, which nearly every Colorado jurisdiction requires, and a license must be obtained separately in each jurisdiction where the contractor will pull permits.
How local licensing works in Colorado
How local licensing works. Each Colorado jurisdiction licenses building contractors under its own ordinance and building code, and there is no state board above them. Class letters and size thresholds differ from place to place, so a Class B in Fort Collins is not a Class B in Colorado Springs. What is consistent is the exam: most jurisdictions require an ICC National Standard contractor examination, open book and multiple choice through Pearson VUE, and the Pikes Peak notice explains why that matters - "with successful passage of an ICC contractor exam, contractors can be secure in the knowledge that their results may be honored by many jurisdictions in Colorado and throughout the United States. However, each jurisdiction has the right to determine if this exam is acceptable." The same exam appears as W11, F11 or G11 for the unlimited (A) tier and W12, F12 or G12 for the limited (B) tier, depending on which code edition the jurisdiction has adopted, and departments generally require results from the current or a recent code year. The notice also warns that "passing an ICC contractor exam is NOT a license to practice and does not guarantee licensing in any jurisdiction."
Denver. The individual first earns a supervisor certificate. Class A covers "to erect, add to, alter, demolish, or repair any building or structure" and needs seven years of notarized commercial experience including ground-up high-rise work over 75 feet plus ICC exam #F11. Class B covers any building classified as less than a high rise and needs four years of notarized commercial experience on ground-up builds of 55 to 75 feet plus ICC exam #F12; Class B-2 caps the highest floor level or occupiable roof at 30 feet, with four years of experience including ground-up projects up to 40 feet, also on ICC #F12. Certificates cost $60 and renew every three years. The company then buys the General Contractor Class A or Building Contractor Class B license at $250 for three years. Denver states it "does not accept or reciprocate contractor licenses and/or certificates from other counties or states."
Colorado Springs, El Paso County and nearby towns (Pikes Peak Regional Building Department). Building Contractor A-1 covers "the construction, alteration and repair of any type or size of structure permitted by the Regional Building Code"; A-2 is the same except Group A, E and I occupancies over 30,000 square feet and any building requiring Type I construction; B-1 covers all occupancies except Groups A, E, I and H and Type I construction; B-2 covers nonstructural remodeling plus Group B, F, M or S buildings up to one storey and 7,500 square feet and Group R buildings up to 16 units and two storeys. License fees are $200 for A-1 and A-2, $175 for B-1 and B-2, on top of a $50 non-refundable application fee, and each of these classes requires an exam. Applicants supply three reference forms documenting experience, copies of all licenses held inside or outside Colorado, liability insurance naming PPRBD, workers' compensation, a Colorado certificate of good standing and a name-based judicial record check. Files close three weeks before the monthly Licensing Committee meeting, the Board of Review approves the following week, and the license must be claimed within 60 days. PPRBD accepts ICC National Standardized or ICC Colorado Standard exams passed on or after January 1, 2016 and states that "no out-of-state exams will be accepted."
Aurora. A single Commercial Building Contractor license "Requires ICC General Building Contractor 'A' OR 'B' Certification"; the supervisor license fee is $131 and the license fee is $392, plus registration and three job references. Limited Building Commercial and Demolition contractors register with three years of documented experience instead.
Fort Collins. Class A and A(DR) cover any building or structure; Class B and B(DR) cover new builds up to and including five storeys; Class C1 and C2 cover new builds up to three storeys and multi-family housing projects; E(C) covers nonstructural commercial alterations. Classes A and B require ICC exam G11 over the 2018 IBC plus the concrete manual, and Classes C1, C2 and E(C) require ICC exam G12, with G11 also accepted in place of G12. Every general contractor class also needs three project verifications with permits and final inspection records signed by someone unconnected to the applicant, and general liability of $1,000,000 per person with $2,000,000 per accident, property damage and aggregate. A new license with supervisor certificate is $300 for a two-year term including a $75 non-refundable application fee; renewals are $225. The city adopted the 2024 ICC codes with amendments in December 2025 and requires exam results from a current code year.
Boulder. Class A covers "the construction, alteration, wrecking, or repair of any type or size of building or structure permitted in the City of Boulder" and requires the ICC A Contractors certificate; Class B covers commercial and residential buildings of construction types V, IV, III-B and II-B and requires the ICC B certificate. New Class A and Class B applicants must also document education, training or years of experience in non-residential construction. Boulder states that it "does not accept reciprocal licenses from other jurisdictions," and its license covers work inside city limits only.
Jefferson County. Class A (labeled 2018 G11) covers "the construction, alteration, tenant finish or repair of any type of structure permitted by the Building Code" and Class B (2018 G12) covers commercial buildings and single- or multi-dwelling buildings up to three storeys. The county accepts "proof that you have passed an appropriate ICC exam within the last 3 years or ... a copy of a valid license issued from an ICC participating jurisdiction." The fee is $50 and licenses renew annually.
Arapahoe County. Building Contractor Class A (commercial) and Class B (commercial/residential) each cost $360 and require the matching ICC certification "or equivalent" certification by a recognized state or national certification entity; Class D specialty is $84. Insurance must carry a $2,000,000 general aggregate and $1,000,000 each occurrence, with the county as an additional holder.
Lakewood. Class A-1 Unlimited Commercial is "only issued to contractors with experience in building high-rise construction"; A-2 Limited Commercial is limited to two-storey commercial or four-storey R occupancies; A-4 covers commercial and residential remodeling not exceeding 30 percent of the original structure. A-1 and A-2 applicants attach any ICC certifications they or their employees hold. Fees are $150 for the first probationary year and $400 for each subsequent three-year renewal.
Douglas County. Unincorporated Douglas County registers general contractors rather than licensing them and states that it "has no testing requirements." Registration needs the application, workers' compensation proof or an exemption statement and business liability insurance naming the Building Division; fees are currently waived.
Out-of-state holders. None of the jurisdictions reviewed will convert another state's general contractor license into a Colorado one. Denver and Boulder rule it out in writing, and PPRBD will not accept exam results earned out of state. What does carry across is the ICC National Standard contractor certification: pass the (A) or (B) exam on a code edition the jurisdiction currently accepts and it will usually satisfy the testing requirement in Denver, Colorado Springs, Aurora, Fort Collins, Boulder, Jefferson County and Arapahoe County, though each department still verifies experience, references or project history separately and charges its own fee. Jefferson County goes further and accepts a current license from another ICC participating jurisdiction in place of the exam. Check the required class, exam code year and fee with each building department before applying, and expect to hold a license in every jurisdiction where you pull permits.
- Denver (Community Planning and Development)
- Colorado Springs / El Paso County (Pikes Peak Regional Building Department)
- Aurora (Building Division)
- Fort Collins (Planning and Development Services)
- Lakewood (Public Works)
- Boulder
- Jefferson County (Division of Building Safety)
- Arapahoe County (Building Division)
- Douglas County (Building Division)
Common questions
- Do I have to take the New Mexico general contractor exam if I'm licensed in Colorado?
- The trade exam is waived, but New Mexico requires a law or code exam.
- How long do I need to have held my Colorado license?
- At least 1 year before applying.
- What does it cost to get a New Mexico general contractor license from Colorado?
- Published fees on this path total $667.94, not counting exam vendor fees or bonds.
- Do my Colorado work hours count in New Mexico?
- Yes. Documented out-of-state experience counts toward New Mexico's eligibility requirements.
- Does it work the other way, from New Mexico to Colorado?
- Not necessarily. Reciprocity is directed. Going from New Mexico to Colorado, the mechanism is not applicable.
Sources
- NASCLA Accredited Examination for Commercial General Building Contractors · National Association of State Contractors Licensing Agencies · Other · verified September 17, 2026
- Construction Industries Licensing Act, NMSA 1978 Chapter 60, Article 13 (RLD compilation as of July 1, 2021) · NMSA 1978 §§ 60-13-3, 60-13-14, 60-13-14.1, 60-13-23, 60-13-49 · New Mexico Regulation and Licensing Department · Statute · verified September 17, 2026
- 14.5.5 NMAC - Construction Industries General Provisions: Fees · 14.5.5.8 and 14.5.5.14 NMAC · New Mexico Commission of Public Records, State Records Center and Archives · Admin Rule · verified September 17, 2026
- 14.6.3 NMAC - Construction Industries Licensing: Contractor's License Requirements · 14.6.3.8 NMAC · New Mexico Commission of Public Records, State Records Center and Archives · Admin Rule · verified September 17, 2026
- 14.6.6 NMAC - Construction Industries Licensing: Classifications and Scopes of Work · 14.6.6.8 and 14.6.6.9 NMAC · New Mexico Commission of Public Records, State Records Center and Archives · Admin Rule · verified September 17, 2026
- NM CID - How to Obtain a Contractor License and Contractor License Application (updated October 2023) · PSI Services for the New Mexico Construction Industries Division · Form · verified September 17, 2026
- State of New Mexico Contractor (Qualifying Party) Examinations Candidate Information Bulletin (PSI) · PSI Services for the NM Construction Industries Division · Other · verified September 17, 2026
- New Mexico Contractor Licensing - Frequently Asked Questions (CID / PSI) · PSI Services for the New Mexico Construction Industries Division · Faq · verified September 17, 2026
- PSI General Building Work Experience Verification - New Mexico Contractor Licensing Service · PSI Services for the New Mexico Construction Industries Division · Form · verified September 17, 2026
- New Mexico Licensing Fees (CID contractor, qualifying party and journeyman fee schedule) · PSI Services for the New Mexico Construction Industries Division · Other · verified September 17, 2026
- NM CID Qualifying Party Certificate Application and Instructions (instructions updated May 2025, form updated August 2025) · PSI Services for the New Mexico Construction Industries Division · Form · verified September 17, 2026
- NM Regulation and Licensing Department - Apply for a Construction Industries License · New Mexico Regulation and Licensing Department, Construction Industries Division · Agency Page · verified September 17, 2026
Verified dates are when a person last opened each source and confirmed the facts above. Cite the board, not us.