LicensebyState

Colorado to South Carolina: general contractor license reciprocity

No credit· Start overVerified September 17, 2026· 7 sources

Colorado does not issue a statewide general contractor license, so there is nothing to transfer. Here is South Carolina's standard path for out-of-state applicants.

Your origin state does not issue a statewide license at this level, so there is no license to transfer. The destination's standard out-of-state path is shown; expect to meet it in full.

Reference only, not legal advice. Rules change; confirm with the licensing board before you apply. Full disclaimer.

Qualifying party certification by NASCLA examination or by South Carolina examination (states without a waiver agreement)

Your out-of-state credentials give no advantage. You meet the destination's requirements from scratch.

South Carolina accepts the NASCLA Accredited Examination for Commercial General Building Contractors in place of its own building technical examination. The Board is a participating agency in the NASCLA program, its Technical Exam Waiver Agreements chart maps the NASCLA Commercial General Building Contractors exam to the South Carolina Unlimited Building classification, and it says it accepts all states administering that exam; the candidate has NASCLA send the transcript directly to the Board. NASCLA does not waive the South Carolina Business Management & Law for Commercial Contractors examination, which every qualifying party must pass. An applicant without the NASCLA credential sits the South Carolina Limited Building or Unlimited Building technical examination through PSI instead. On either route the qualifying party files Doc. 168 with at least two years of full-time work experience performed within the past five years in the classification applied for, primarily commercial, documented on the Work Experience Affidavit (Doc. 167); experience earned in other states counts. The business then files Doc. 165 with the $350 licensure fee, its Secretary of State verification and a financial statement or surety bond for the group limit it wants.

S.C. Code Section 40-11-290 also allows the Board to exempt the technical examination for an applicant who can verify passing an examination in another state that is essentially the same as South Carolina’s, even without a reciprocal agreement, but the Board publishes no separate procedure for that outside the Technical Exam Waiver Agreements list and the NASCLA route. The examination score needed is 70 percent, an individual may sit a given examination twice in a twelve-month period and once every six months after that, and a certification left inactive four or more years has to be re-examined. Successful completion of a PHCC Academy of North Carolina apprenticeship is listed on Doc. 168 as an alternative to the two-year work experience affidavit. The Board publishes no processing time and no PSI fee amounts; contact it at [email protected] or (803) 896-4686.

At a glance

Trade exam
Waived
Law / code exam
Required
Out-of-state hours
Count toward eligibility

What you must already have

  • You must have passed a licensing exam in Colorado that the destination considers comparable.The Board’s licensure page lists "NASCLA: Contact NASCLA to have your transcripts sent directly to the Board" as a method of qualifying by examination, its NASCLA program handout states that the Board "is a participating state agency in administering the National Commercial Building Contractor exam, and the NASCLA Accredited Trade Examination for Electrical Contractors through the testing provider, PSI Exams", and the Technical Exam Waiver Agreements chart maps the NASCLA Commercial General Building Contractors exam to the Unlimited Building classification while accepting all states that administer it. The NASCLA exam is an examination credential rather than a license or a state-to-state agreement, so any candidate may sit it in any participating jurisdiction. It does not waive the South Carolina Business Management & Law for Commercial Contractors examination, the work experience requirement, the licensure fee or the financial responsibility requirement.
  • At least two years of full-time work experience performed within the past five years in the license classification or subclassification applied for, primarily commercial. Experience earned in other states counts and is documented on the Work Experience Affidavit (Doc. 167) by former or current employers.S.C. Code Section 40-11-230(B)(2) states the requirement for designation as a primary qualifying party and allows the Board to accept other proof of employment experience. Doc. 168 also accepts a Certificate of Achievement from a PHCC Academy of North Carolina apprenticeship in Heating, Air Conditioning and Plumbing in place of the affidavit, which matters for mechanical rather than building classifications.
  • The primary qualifying party must serve in a management capacity for the licensee, be actively involved in its management, supervision and operations, and may not take other employment that conflicts with those duties (S.C. Code Section 40-11-230(B)(3)).

What you'll do to get licensed in South Carolina

  1. 1Trade exam. Pass the destination's trade exam (if applicable). South Carolina Limited Building or Unlimited Building technical examination through PSI, registered at https://test-takers.psiexams.com/sccon. It is required unless the qualifying party brings the NASCLA Accredited Examination for Commercial General Building Contractors or an accepted examination from a jurisdiction on the Technical Exam Waiver Agreements list. The limited building contractor examination or the unlimited general contractor examination qualifies a Group 1, 2 or 3 license and the unlimited examination is required for Groups 4 and 5; structures built under a limited building examination are restricted to three stories in height..
  2. 2Law / code exam. Pass a law, rules, or code exam. South Carolina Business Management & Law for Commercial Contractors examination, administered by PSI. Every individual must pass it before the Board will certify them as a qualifying party, no matter which route they use to satisfy the technical examination. Register at https://test-takers.psiexams.com/sccon. S.C. Code Section 40-11-230 requires a grade of 70 percent or better, and an individual may sit a given examination only twice in a twelve-month period and once every six months after that..
  3. 3Exam fee. Pay the exam fee. PSI examination fees are paid directly to PSI when the examination is scheduled. The Board does not publish the amounts; the current fees are in PSI’s South Carolina candidate information bulletin at https://test-takers.psiexams.com/sccon, or call PSI at (855) 746-8173..
  4. 4License fee. Pay the license or certificate fee ($350). Non-refundable $350 licensure fee, paid by check or money order to SCCLB with the General and Mechanical Contractor Application for Licensure (Doc. 165). No cash is accepted and a returned-check fee of up to $30 may be charged. General Contractor licenses expire on October 31 in even-numbered years..
  5. 5Financial responsibility. Show financial responsibility of at least $10,000. Financial statement for the entity that will hold the license, sized by the license group it wants, with a balance sheet dated no more than twelve months before the application. For General Contractors the groups are: Group 1, bids and jobs up to $100,000, working capital $10,000 or net worth $20,000; Group 2, up to $400,000, $40,000 or $60,000; Group 3, up to $1,000,000, $100,000 or $150,000; Group 4, up to $3,000,000, $175,000 or $250,000; Group 5, unlimited, $250,000 or $350,000. Only one of working capital or net worth has to be met. Groups 1 and 2 may file the owner-prepared statement with an affidavit of accuracy (Doc. 172); Groups 3 and 4 need a statement compiled by a licensed CPA in accordance with GAAP; Group 5 needs an audited balance sheet from a licensed CPA. The figure shown is the Group 1 working capital minimum (S.C. Code Section 40-11-260)..
  6. 6Surety bond. Post a surety bond ($20,000) (if applicable). Optional alternative to the financial statement under S.C. Code Section 40-11-262: a surety bond in the same amount as the net worth required for the license group, so $20,000 for Group 1, $60,000 for Group 2, $150,000 for Group 3, $250,000 for Group 4 and $350,000 for Group 5. The surety must be authorized to transact surety business in South Carolina, the bond is continuous, lists the State of South Carolina as obligee, and stays in force until the licensee files a financial statement meeting its group. The original must carry the surety’s signature, the principal’s signature, a visible surety company seal and the attached power of attorney; DocuSign is not accepted, and a bond payable to the Residential Builders Commission is not accepted by this Board. The figure shown is the Group 1 bond..
  7. 7Business license. Obtain a business license. The license is issued to the business, so the entity must be able to conduct business in South Carolina. Attach a Certificate of Existence (or Good Standing) from the SC Secretary of State if the company was incorporated in South Carolina, or a Certificate of Authority if it was incorporated in another state, together with the articles of incorporation or organization and documentation of each owner’s percentage. This is not required for a sole proprietorship..
  8. 8Other. Primary Qualifying Party / Qualifying Party Initial Application (Doc. 168) for each qualifying party who is not already certified or has been inactive more than four years, with a copy of a driver’s license, state-issued ID, passport or military ID, a copy of the Social Security card, a notarized Verification of Lawful Presence form, the PQP/QP Company Acknowledgement Affidavit (Doc. 190), examination score sheets, and official license verifications from every other state where you are or have been licensed..

Published fees on this path total $350, excluding exam-vendor fees, bonds, and insurance.

What you'll need to buy or arrange

Exam preparation

Most boards contract PSI, Prov, or ICC for exams. Check which code edition the exam is written to before buying a prep course.

  • Trade exam · if applicable
  • Law / code exam
  • Exam fee

Surety bond

A license or contractor bond is bought from a surety, not the state. Price is a small percentage of the bond amount and depends on your credit.

  • Surety bond · $20,000 · if applicable

Business registration

If you plan to contract in your own name, budget for a business license or entity registration on top of the trade license.

  • Business license

How South Carolina licenses general contractors

South Carolina general contractor · “General Contractor license, Building classification (Limited Building or Unlimited Building), Group 1-5

Statewide license

Verified September 17, 2026· 5 sources

Issued by South Carolina Contractor’s Licensing Board (SC LLR)

Commercial and unlimited building work in South Carolina runs through the Contractor’s Licensing Board, which licenses General Contractors for any general contracting where the total cost of construction is more than $10,000. The license belongs to the business, not to the person: an individual, corporation, LLC or partnership holds it and must designate a Primary Qualifying Party for each classification, an individual in a management role who personally passes the examinations, so an inbound contractor applies as or for the entity that will sign contracts and pull permits. The Building classification covers commercial, industrial, institutional, modular and all other building construction including residential structures, and carries the Wood Frame Structures, Nonstructural Renovation, Masonry, Pre-engineered Metal Buildings, Roofing, Structural Framing and Miscellaneous Metals subclassifications. Every license also carries a group limit driven by money rather than skill: Group 1 bids and jobs up to $100,000 through to Group 5 with no cap, each set by working capital, net worth or a surety bond. The qualifying party for a Group 1, 2 or 3 license passes either the limited building contractor examination or the unlimited general contractor examination, while Groups 4 and 5 require the unlimited examination, and structures built under a limited building examination are restricted to three stories.

Moving to South CarolinaLeaving South Carolina

Why Colorado has nothing to transfer

Colorado general contractor · “General / Building contractor license (Class A or B in most jurisdictions)

Licensed by cities and counties

Verified September 17, 2026· 18 sources

Colorado has no statewide general or commercial building contractor license. DORA licenses electricians and plumbers through its Division of Professions and Occupations but states on its own consumer page that general contractors are not licensed at the state level and that you should check with the city; the Pikes Peak Regional Building Department says the same thing in its exam notice. Unlimited and commercial building work is therefore licensed by each city, county or regional building department, typically as a Class A (unlimited) and Class B (limited commercial or under a height or storey cap) pair: Denver issues General Contractor Class A and Building Contractor Class B, Colorado Springs issues Building Contractor A-1, A-2, B-1 and B-2, Fort Collins issues Classes A, B, C1 and C2, and Aurora issues a single Commercial Building Contractor license. The license is held by the business and qualified by an individual who holds the supervisor certificate and has passed the relevant exam, so the person moving states applies for the certificate and the company applies for the license. The common thread is the ICC National Standard General Building Contractor (A) and Building Contractor (B) examinations, which nearly every Colorado jurisdiction requires, and a license must be obtained separately in each jurisdiction where the contractor will pull permits.

How local licensing works in Colorado

How local licensing works. Each Colorado jurisdiction licenses building contractors under its own ordinance and building code, and there is no state board above them. Class letters and size thresholds differ from place to place, so a Class B in Fort Collins is not a Class B in Colorado Springs. What is consistent is the exam: most jurisdictions require an ICC National Standard contractor examination, open book and multiple choice through Pearson VUE, and the Pikes Peak notice explains why that matters - "with successful passage of an ICC contractor exam, contractors can be secure in the knowledge that their results may be honored by many jurisdictions in Colorado and throughout the United States. However, each jurisdiction has the right to determine if this exam is acceptable." The same exam appears as W11, F11 or G11 for the unlimited (A) tier and W12, F12 or G12 for the limited (B) tier, depending on which code edition the jurisdiction has adopted, and departments generally require results from the current or a recent code year. The notice also warns that "passing an ICC contractor exam is NOT a license to practice and does not guarantee licensing in any jurisdiction."

Denver. The individual first earns a supervisor certificate. Class A covers "to erect, add to, alter, demolish, or repair any building or structure" and needs seven years of notarized commercial experience including ground-up high-rise work over 75 feet plus ICC exam #F11. Class B covers any building classified as less than a high rise and needs four years of notarized commercial experience on ground-up builds of 55 to 75 feet plus ICC exam #F12; Class B-2 caps the highest floor level or occupiable roof at 30 feet, with four years of experience including ground-up projects up to 40 feet, also on ICC #F12. Certificates cost $60 and renew every three years. The company then buys the General Contractor Class A or Building Contractor Class B license at $250 for three years. Denver states it "does not accept or reciprocate contractor licenses and/or certificates from other counties or states."

Colorado Springs, El Paso County and nearby towns (Pikes Peak Regional Building Department). Building Contractor A-1 covers "the construction, alteration and repair of any type or size of structure permitted by the Regional Building Code"; A-2 is the same except Group A, E and I occupancies over 30,000 square feet and any building requiring Type I construction; B-1 covers all occupancies except Groups A, E, I and H and Type I construction; B-2 covers nonstructural remodeling plus Group B, F, M or S buildings up to one storey and 7,500 square feet and Group R buildings up to 16 units and two storeys. License fees are $200 for A-1 and A-2, $175 for B-1 and B-2, on top of a $50 non-refundable application fee, and each of these classes requires an exam. Applicants supply three reference forms documenting experience, copies of all licenses held inside or outside Colorado, liability insurance naming PPRBD, workers' compensation, a Colorado certificate of good standing and a name-based judicial record check. Files close three weeks before the monthly Licensing Committee meeting, the Board of Review approves the following week, and the license must be claimed within 60 days. PPRBD accepts ICC National Standardized or ICC Colorado Standard exams passed on or after January 1, 2016 and states that "no out-of-state exams will be accepted."

Aurora. A single Commercial Building Contractor license "Requires ICC General Building Contractor 'A' OR 'B' Certification"; the supervisor license fee is $131 and the license fee is $392, plus registration and three job references. Limited Building Commercial and Demolition contractors register with three years of documented experience instead.

Fort Collins. Class A and A(DR) cover any building or structure; Class B and B(DR) cover new builds up to and including five storeys; Class C1 and C2 cover new builds up to three storeys and multi-family housing projects; E(C) covers nonstructural commercial alterations. Classes A and B require ICC exam G11 over the 2018 IBC plus the concrete manual, and Classes C1, C2 and E(C) require ICC exam G12, with G11 also accepted in place of G12. Every general contractor class also needs three project verifications with permits and final inspection records signed by someone unconnected to the applicant, and general liability of $1,000,000 per person with $2,000,000 per accident, property damage and aggregate. A new license with supervisor certificate is $300 for a two-year term including a $75 non-refundable application fee; renewals are $225. The city adopted the 2024 ICC codes with amendments in December 2025 and requires exam results from a current code year.

Boulder. Class A covers "the construction, alteration, wrecking, or repair of any type or size of building or structure permitted in the City of Boulder" and requires the ICC A Contractors certificate; Class B covers commercial and residential buildings of construction types V, IV, III-B and II-B and requires the ICC B certificate. New Class A and Class B applicants must also document education, training or years of experience in non-residential construction. Boulder states that it "does not accept reciprocal licenses from other jurisdictions," and its license covers work inside city limits only.

Jefferson County. Class A (labeled 2018 G11) covers "the construction, alteration, tenant finish or repair of any type of structure permitted by the Building Code" and Class B (2018 G12) covers commercial buildings and single- or multi-dwelling buildings up to three storeys. The county accepts "proof that you have passed an appropriate ICC exam within the last 3 years or ... a copy of a valid license issued from an ICC participating jurisdiction." The fee is $50 and licenses renew annually.

Arapahoe County. Building Contractor Class A (commercial) and Class B (commercial/residential) each cost $360 and require the matching ICC certification "or equivalent" certification by a recognized state or national certification entity; Class D specialty is $84. Insurance must carry a $2,000,000 general aggregate and $1,000,000 each occurrence, with the county as an additional holder.

Lakewood. Class A-1 Unlimited Commercial is "only issued to contractors with experience in building high-rise construction"; A-2 Limited Commercial is limited to two-storey commercial or four-storey R occupancies; A-4 covers commercial and residential remodeling not exceeding 30 percent of the original structure. A-1 and A-2 applicants attach any ICC certifications they or their employees hold. Fees are $150 for the first probationary year and $400 for each subsequent three-year renewal.

Douglas County. Unincorporated Douglas County registers general contractors rather than licensing them and states that it "has no testing requirements." Registration needs the application, workers' compensation proof or an exemption statement and business liability insurance naming the Building Division; fees are currently waived.

Out-of-state holders. None of the jurisdictions reviewed will convert another state's general contractor license into a Colorado one. Denver and Boulder rule it out in writing, and PPRBD will not accept exam results earned out of state. What does carry across is the ICC National Standard contractor certification: pass the (A) or (B) exam on a code edition the jurisdiction currently accepts and it will usually satisfy the testing requirement in Denver, Colorado Springs, Aurora, Fort Collins, Boulder, Jefferson County and Arapahoe County, though each department still verifies experience, references or project history separately and charges its own fee. Jefferson County goes further and accepts a current license from another ICC participating jurisdiction in place of the exam. Check the required class, exam code year and fee with each building department before applying, and expect to hold a license in every jurisdiction where you pull permits.

Moving to ColoradoLeaving Colorado

Common questions

Do I have to take the South Carolina general contractor exam if I'm licensed in Colorado?
The trade exam is waived, but South Carolina requires a law or code exam.
What does it cost to get a South Carolina general contractor license from Colorado?
Published fees on this path total $350, not counting exam vendor fees or bonds.
Do my Colorado work hours count in South Carolina?
Yes. Documented out-of-state experience counts toward South Carolina's eligibility requirements.
Does it work the other way, from South Carolina to Colorado?
Not necessarily. Reciprocity is directed. Going from South Carolina to Colorado, the mechanism is not applicable.

Sources

  1. NASCLA Accredited Examination for Commercial General Building Contractors · National Association of State Contractors Licensing Agencies · Other · verified September 17, 2026
  2. S.C. Code of Laws Title 40, Chapter 11 - Contractors · S.C. Code Ann. Sections 40-11-30, 40-11-230, 40-11-260, 40-11-262, 40-11-290, 40-11-410 · South Carolina Legislature · Statute · verified September 17, 2026
  3. General and Mechanical Contractor Application for Licensure and Instructions (Doc. 165, 12/22/2025 v2.2) · South Carolina Department of Labor, Licensing and Regulation (LLR) · Form · verified September 17, 2026
  4. General and Mechanical Contractors - Primary Qualifying Party (PQP) and Qualifying Party (QP) Initial Application (Doc. 168, 12/19/2025 v2.1) · South Carolina Department of Labor, Licensing and Regulation (LLR) · Form · verified September 17, 2026
  5. SC Contractor’s Licensing Board - Licensure with the Board (application, qualifying parties, exams, group limits, financial statements, bonds) · South Carolina Department of Labor, Licensing and Regulation (LLR) · Agency Page · verified September 17, 2026
  6. SC Contractor’s Licensing Board - NASCLA Accredited Examination Program (board handout) · South Carolina Department of Labor, Licensing and Regulation (LLR) · Agency Page · verified September 17, 2026
  7. SC Contractor’s Licensing Board - Technical Exam Waiver Agreements (as of May 2026, Revised 5/2026) · South Carolina Department of Labor, Licensing and Regulation (LLR) · Agreement Document · verified September 17, 2026

Verified dates are when a person last opened each source and confirmed the facts above. Cite the board, not us.

Report an error on this page

Related