Illinois to Oregon: general contractor license reciprocity
Illinois does not issue a statewide general contractor license, so there is nothing to transfer. Here is Oregon's standard path for out-of-state applicants.
Your origin state does not issue a statewide license at this level, so there is no license to transfer. The destination's standard out-of-state path is shown; expect to meet it in full.
Reference only, not legal advice. Rules change; confirm with the licensing board before you apply. Full disclaimer.
CCB application with the NASCLA examination in place of the pre-license training (every state)
Your out-of-state credentials give no advantage. You meet the destination's requirements from scratch.
Oregon has no contractor reciprocity at the commercial level either. OAR 812-006-0300(6) states that there are no reciprocal agreements with other states or with organizations that test contractors, and ORS chapter 701 contains no provision recognizing a license issued elsewhere, so an out-of-state general contractor license buys nothing on its own. The Board does accept the NASCLA Accredited Examination for Commercial General Building Contractors: under OAR 812-006-0310 an RMI who has passed it satisfies the 16-hour pre-license training requirement, regardless of when the exam was taken, and needs only the Oregon contractor test, with the pass established by the RMI's entry in the NASCLA National Examination Database rather than by a transcript from the candidate. An RMI without it completes 16 hours of approved training and then takes the same Oregon test, which is the state's only examination: 80 scored questions in 180 minutes, 70 percent to pass, open book on Oregon laws, rules and business practices, and never waived. Out-of-state work does count in one place at this level: the eight combined years for Level 1 or four for Level 2 are certified by the contractor for its key employees and the statute nowhere requires the experience to have been earned in Oregon, so years spent as a licensed contractor, journeyman, foreperson or supervisor in another state count toward the endorsement. The remaining steps are the same for every applicant: registration with the Oregon Secretary of State, an $80,000 or $25,000 commercial bond and $2 million or $1 million of aggregate liability insurance on the Board's own forms according to the level chosen, workers' compensation cover if the business has employees, and the $400 application fee.
Level 1 and Level 2 are licensed to perform identical work, so the choice between them is a choice about experience, bond size, insurance limit and continuing education rather than about scope. The key-employee experience is certified by the contractor on the application and again at renewal; the Board publishes no verification form for it and no list of documents it will accept, so confirm with the licensing call center on 503-378-4621 what evidence it wants for years worked outside Oregon. Two other RMI routes exist but rarely help an inbound contractor: continuous association with an Oregon-licensed business from before 1 July 2000 with no lapse over 24 months, and a sole proprietor exemption under Oregon Laws 2018 chapter 46, which in any case only produces a residential endorsement. OAR 812-003-0265 separately gives the spouse of an active-duty servicemember stationed in Oregon a temporary authorization of up to two years, available for both commercial general levels, on a current out-of-state general, commercial or residential contractor license in good standing, with competency shown by the NASCLA examination, the Oregon examination, or eight years of licensed contracting in another state, plus three hours of Board education. The license must be applied for within two years of passing the Oregon test, and the Board charges no separate fee for the endorsement on a new application.
At a glance
- Trade exam
- Waived
- Law / code exam
- Required
- Out-of-state hours
- Count toward eligibility
- Typical processing
- About 42 days
What you must already have
- You must have passed a licensing exam in Illinois that the destination considers comparable.OAR 812-006-0310 accepts the pass whenever it was earned and proves it by the RMI's name appearing in the NASCLA National Examination Database. The NASCLA examination is an exam credential rather than a license or an interstate agreement, so it is open to a candidate from any state and confers no advantage tied to where the applicant is licensed. It does not waive the Oregon contractor test, the key-employee experience, the bond, the insurance or the fee. An applicant without it takes 16 hours of approved training instead.
- For Commercial General Contractor Level 1, one or more key employees with a combined total of at least eight years of construction experience; for Level 2, a combined total of at least four years. A key employee is an owner or employee who is a corporate officer, manager, superintendent, foreperson or lead person.The qualifying years are time worked as a licensed contractor, journeyman, foreperson or supervisor or as any other employee engaged in construction work for a licensed contractor, and ORS 701.050 does not confine that to Oregon, so out-of-state years count. Completion of an apprenticeship substitutes for up to three years, a bachelor's degree in a construction-related field for up to three, a bachelor's or master's degree in business, finance or economics for up to two, and an associate's degree in construction or building management for one. The contractor certifies the total on the application and at every renewal.
- The business must designate at least one Responsible Managing Individual: an owner or an employee who exercises management or supervisory authority over the construction activities of the business. An RMI who is not an owner may serve only one licensee at a time, and a business that loses its RMI must appoint a replacement immediately or a temporary RMI for no more than 14 days, or the license is suspended.
- You must have no disciplinary action or unresolved complaints on your record.ORS 701.098(1)(d). The application also requires five years of construction-related court judgments, administrative orders, pending complaints, convictions and indictments from any state, and unsatisfied construction debt blocks a new license for the business owners and for the RMI until it is paid.
What you'll do to get licensed in Oregon
- 1Other. At least 16 hours of pre-license training on business practices and law from a CCB-approved education provider, taken by the RMI. It is required of every applicant except an RMI who has passed the NASCLA Accredited Examination for Commercial General Building Contractors, and except the narrow RMI route based on continuous Oregon licensure from before July 2000. Providers set their own prices, so the Board publishes no figure; the approved provider list is on the CCB site and the education team can be reached on 503-934-2227. (if applicable).
- 2Law / code exam. Pass a law, rules, or code exam. The Oregon contractor test, administered by PSI at test centers in Oregon and other states or by remote proctor: 80 scored questions in 180 minutes, plus 8 unscored questions and 20 minutes, with 70 percent needed to pass. It is open book against the NASCLA Contractors Guide to Business, Law and Project Management for Oregon Construction Contractors, 2nd edition, which may be highlighted, tabbed and annotated beforehand. The subjects are Oregon contractor laws and regulations, business structure, employees, subcontractors, contracts, lien law, bidding and estimating, project management, building codes, jobsite safety, environmental factors, exterior shell, financial management and tax basics. There is no separate commercial or trade examination. A failed test may be retaken without limit, though not the same version on consecutive attempts, and the license application must follow within two years of the pass..
- 3Exam fee. Pay the exam fee ($60). PSI examination fee, payable when the test is scheduled. It covers first-time and repeat takers and stays valid for one year from the date of payment..
- 4Application fee. Pay the application fee ($400). CCB license application fee for a new license, set at $400 for applications received from 1 July 2025. It covers the two-year license; renewal is a further $400 every two years, and changing or adding an endorsement later costs $20. Application fees are not refunded. A licensee who is a sole proprietor or general partner on active duty in the armed forces does not pay a renewal fee falling due during that service..
- 5Surety bond. Post a surety bond ($25,000). A commercial surety bond sized to the level chosen: $25,000 for Commercial General Contractor Level 2 and $80,000 for Level 1. The Board accepts only its own CCB Commercial Surety Bond form, signed by an authorized agent of the surety or an attorney-in-fact, bearing a bond number, and filed within 60 days of the date the surety executed it. A commercial bond answers only for small and large commercial work, so a contractor also taking a residential endorsement posts a second, residential bond. Commercial Specialty Level 1 is $55,000 and Level 2 $25,000..
- 6Insurance. Carry the required insurance ($1,000,000). General liability insurance sized to the level chosen: at least $1 million aggregate for Commercial General Contractor Level 2 and at least $2 million aggregate for Level 1, covering products and completed operations, with the certificate naming Construction Contractors Board, PO Box 14140, Salem, OR 97309 as certificate holder. Proof is filed with the application and again at every renewal. A contractor holding both a commercial and a residential endorsement carries a single policy at the higher of the two amounts..
- 7Insurance. Carry the required insurance (if applicable). Workers' compensation coverage, required of any business that is non-exempt, meaning it has employees. A sole proprietor with no employees, and a business in which every owner, officer or member is a family member, may file as exempt; the Board defines family as parents, spouses, sisters, brothers, daughters, sons, daughters-in-law, sons-in-law and grandchildren. A non-exempt applicant supplies its carrier, policy number, Workers' Compensation Division compliance number and employer tax identification numbers, and any change between exempt and non-exempt status must be reported to the Board within 10 days..
- 8Business license. Obtain a business license. A business entity that is required to register with the Oregon Secretary of State's Corporation Division must be registered, active and in good standing before the license issues, and every assumed business name used by the applicant must be registered as that entity's assumed business name. An out-of-state entity registers in Oregon in the same way. A joint venture is licensed and endorsed for bidding purposes if a named partner or joint venturer holds the license and endorsement..
- 9Background check. Complete a background check. The RMI clears a background check after the application is filed. The application itself asks the business and its owners and officers to disclose, for the five years before the application and from any state, unsatisfied construction-related court judgments and administrative orders, pending complaints alleging money owed, and judgments of conviction or indictments for the crimes listed in ORS 701.098, along with unpaid workers' compensation penalties and unpaid employee wages. Unsatisfied construction debt keeps both the owners and the RMI from obtaining a new CCB license until it is paid..
- 10Surety bond. Post a surety bond ($30,000) (if applicable). A separate $30,000 public works bond, filed with the Board before work starts on a qualifying public works project over $100,000. It is not part of the licensing application, but it is the second bond most commercial general contractors in Oregon end up posting. Disadvantaged, minority, women-owned, service-disabled veteran and emerging small businesses certified by the state may apply for an exemption..
- 11Continuing education. Complete continuing education (if applicable). Not required to obtain the license. Each two-year license period a Commercial General Contractor Level 2 must certify that one or more key employees completed at least 32 hours of continuing education; a Level 1 contractor's requirement scales with the lowest number of key employees it had during the period, at 16 hours for one, 32 for two, 48 for three, 64 for four and 80 for five or more. Hours count only if the key employee was employed by the contractor when the course was taken, and hours credited at one renewal cannot be reused at the next. Contractors who also hold certain Oregon licenses, including architect, engineer, electrician and plumber, are exempt..
- 12Other. A contractor whose Oregon work will include boiler, electrical, elevator or plumbing installation also needs the matching Building Codes Division contractor license, and OAR 918-030-0015 requires an active CCB license before the division will issue or renew one. The CCB license comes first, and it does not replace the division license..
Published fees on this path total $460, excluding exam-vendor fees, bonds, and insurance.
What you'll need to buy or arrange
Exam preparation
Most boards contract PSI, Prov, or ICC for exams. Check which code edition the exam is written to before buying a prep course.
- Other · if applicable
- Law / code exam
- Exam fee · $60
Surety bond
A license or contractor bond is bought from a surety, not the state. Price is a small percentage of the bond amount and depends on your credit.
- Surety bond · $25,000
- Surety bond · $30,000 · if applicable
Liability insurance
Some states require proof of general liability or workers' compensation coverage at licensing time.
- Insurance · $1,000,000
- Insurance · if applicable
Business registration
If you plan to contract in your own name, budget for a business license or entity registration on top of the trade license.
- Business license
Continuing education
Renewals usually need approved CE hours, often on the latest NEC. Reciprocal licensees are rarely exempt.
- Continuing education · if applicable
How Oregon licenses general contractors
Oregon general contractor · “Construction contractor license with the Commercial General Contractor Level 1 or Level 2 (CGC1/CGC2) endorsement”
Statewide license
Issued by Oregon Construction Contractors Board (CCB)
Oregon's unlimited tier is the Commercial General Contractor endorsement, carried on the same single construction contractor license the Construction Contractors Board issues to everyone: ORS 701.021 requires a current CCB license plus the endorsement that matches the work, and the endorsement is what sets the bond and the insurance. A Commercial General Contractor may bid or perform work involving an unlimited number of unrelated building trades on small or large commercial structures, and it comes in two levels that are allowed to do exactly the same work and differ only in what stands behind them. Level 1 requires one or more key employees with a combined total of at least eight years of construction experience, an $80,000 commercial bond and general liability insurance of at least $2 million aggregate; Level 2 requires four combined years, a $25,000 commercial bond and at least $1 million aggregate. A key employee is an owner or employee who is a corporate officer, manager, superintendent, foreperson or lead person, the qualifying years are time as a licensed contractor, journeyman, foreperson or supervisor or as another employee doing construction work for a licensed contractor, and an apprenticeship or a construction-related bachelor's degree substitutes for up to three years, a bachelor's or master's in business, finance or economics for up to two, and an associate's degree in construction or building management for one. Alongside it sit Commercial Specialty Contractor Level 1 and Level 2 for one or two unrelated trades and Commercial Developer; a license may carry one commercial endorsement, one residential endorsement, or one of each, and a contractor holding both posts two bonds and carries one liability policy at the higher amount. As at every level the license belongs to the business and must at all times have at least one Responsible Managing Individual, an owner or employee with management or supervisory authority over its construction activities, who has completed 16 hours of CCB-approved pre-license training and passed the Oregon contractor test. Oregon imposes no net worth, working capital or financial statement test; the key-employee experience certification, the bond and the insurance are the only financial gates.
Why Illinois has nothing to transfer
Illinois general contractor · “No statewide license; local titles include Chicago General Contractor Class A, B or C”
Licensed by cities and counties
Illinois has no statewide general, commercial or building contractor license and no state board that examines or qualifies builders, so an out-of-state general contractor license has nothing at the state level to transfer into. The State does license pieces of the work: the Department of Financial and Professional Regulation licenses roofing contractors under the Illinois Roofing Industry Licensing Act, in a limited tier for residential buildings of eight units or less and an unlimited tier for residential, commercial and industrial roofs, and also licenses architects, professional and structural engineers, land surveyors and alarm contractors, while the Department of Public Health licenses plumbers, plumbing contractors and irrigation contractors and separate state programs cover elevator and fire sprinkler contractors. Commercial building itself is controlled by home rule municipalities through the building permit, and the City of Chicago's General Contractor license, graded Class A through E by project value, is by far the most consequential credential in the state. A general contractor arriving in Illinois gets licensed or registered in each jurisdiction where they will pull permits, carries the insurance and bonds those jurisdictions require, and makes sure the roofing, plumbing, electrical and mechanical scopes are performed under the correct state or municipal trade licenses.
How local licensing works in Illinois
How it works in Illinois. No Illinois agency issues a general, commercial, building or unlimited contractor license, and there is no Illinois qualifying party or state business-and-law exam for general building work. Home rule municipalities control commercial construction through the permit, and each one writes its own contractor ordinance, so a contractor is licensed or registered separately in every jurisdiction where they build. Where a city does license, the credential is generally based on insurance, financial solvency, entity documents and a fee rather than on a competence exam, and none of the programs reviewed recognizes a general contractor license issued by another state. What genuinely travels into Illinois is a state trade license: roofing under 225 ILCS 335, plumbing under the Department of Public Health, and the state elevator, fire sprinkler and alarm credentials, all of which cities check before they issue a permit.
Chicago. Chicago's General Contractor license is the one credential that shapes commercial work in Illinois. It is required to bid on, undertake, hire or supervise, or control the means and methods of any 'regulated activity' - work requiring a building, sign or demolition (wrecking) permit, a sewer permit, a Department of Public Health permit for sandblasting, grinding or chemical washing, work exempt from permit under Section 402 of the Chicago Construction Codes Administrative Provisions, or work under a stormwater management plan. Licenses go to businesses, including sole proprietorships, in five classes graded by project value, defined as 'the fair market value of materials and labor provided by all contractors and subcontractors as part of all concurrent and consecutive regulated activities at the same site': Class A unlimited value, ordinary or complex demolition, $5 million per occurrence of insurance, $3,500.00; Class B up to $20 million, ordinary or complex demolition, $3 million, $1,800.00; Class C up to $10 million, ordinary demolition, $2 million, $1,300.00; Class D up to $4 million, ordinary demolition, $2 million, $900.00; Class E up to $500,000, no demolition, $1 million, $300.00. The Class B, C and D project limits and the Class C and D insurance figures took effect January 1, 2026, and for Class C and D licenses issued before that date the higher insurance requirement is enforced when the policy on file expires. Commercial general liability must come from an insurer authorized in Illinois and rated B+ or higher by A.M. Best, covering bodily injury, personal injury, property damage and completed operations, with primary plus excess or umbrella policies allowed above $1 million; the full requirements are in Section 4-36-090 of the Municipal Code. The application also needs a statement of financial solvency on the supplied form, proof of authority to do business in Illinois, an Assumed Name Certificate where a trade name is used, and government photo identification for the controlling persons. There is no exam, no experience review and no qualifying party. Continental Testing Services handles applications and renewals by mail for the Department of Buildings; the license is valid one year and is automatically inactivated if the insurance policy lapses. A licensed general contractor's own employees and subcontractors under its supervision and control do not need their own general contractor license, but electrical, plumbing, mason, drain layer, elevator mechanic and board-up work must be done by the holders of those separate City licenses, and anyone contracting directly with the owner needs their own license and must be listed on the permit.
Cook County (unincorporated areas). Every contractor working in unincorporated Cook County registers with the Department of Building and Zoning: $150 per trade to start and $75 per trade annually by December 31, with $1,000,000 general liability naming Cook County Building and Zoning at 69 W. Washington, Suite 2830, Chicago as certificate holder. The owner or a corporate officer files, with the Articles of Incorporation or current Annual Domestic Report. Roofing registrants file the State of Illinois roofing license and demolition registrants a fully approved bond. No exam. Check the site against the county's CookViewer tool first, because much of suburban Cook County is incorporated and licensed by its own village.
Aurora. A General contractor registration costs $200 and consists of the Contractor Licensing Application, a certificate of insurance naming the City of Aurora as primary and non-contributory additional insured with $1,000,000 general aggregate and $500,000 per occurrence, statutory workers' compensation, and Secretary of State registration or a county DBA certificate. Aurora tests only electrical and mechanical contractors, accepting ICC certifications or licenses from named municipalities in place of its own exam; the General category has no test. Elevator, fire suppression, roofing and sign registrations are also $200, and a dumpster or right-of-way obstruction registration needs a $5,000 surety bond. Delinquent permits will block a renewal.
Evanston. General Contractor registration is $150 a year, renewable through the Citizen Portal, with general liability of at least $300,000 per occurrence, bodily injury and property damage of at least $100,000 per occurrence each, and workers' compensation at statutory minimums naming Evanston as certificate holder. Right-of-way work requires $1,000,000 per occurrence with the city as an additional insured. State-regulated contractors submit a copy of the state license. Trade registration is $125.
Joliet. Registration is required before any permit is issued but costs nothing: 'there are no forms or fees for registration, unless you are a Sign Erector or for HVAC Testing.' The requirement is a certificate of insurance naming the City of Joliet, with minimum limits of $250,000 bodily injury per person, $500,000 bodily injury per occurrence and $250,000 property damage per occurrence. Trade credentials are checked separately: the Illinois State Roofer's License for roofing, the Illinois Plumbing Contractor Registration for plumbing, the State of Illinois elevator license, the Illinois sprinkler (FSC) and private alarm licenses, and a municipal electrical or HVAC license from Joliet's accepted list. Concrete work in the right-of-way needs a $10,000 street obstruction bond and demolition a $50,000 wrecking bond. Electrical, plumbing and HVAC contractors file a project-specific Letter of Intent, and all subcontractors must be listed on the permit application.
Rockford. 'General contractors are not required to be licensed.' Rockford controls commercial work through the permit only, and enforces the State roofing license: 'roofing contractors are required to obtain a license from the State of Illinois Department of Professional Regulation.'
Springfield. The Building and Zoning Department publishes electrical and mechanical contractor license and registration applications and no general contractor registration at all; its building permit application asks for the general contractor's name and address but for a license number only on the roofing line. Building and Zoning, 300 South 7th Street, Room 304, (217) 789-2171.
Peoria. Peoria licenses electrical and HVAC contractors individually at $150.00 each, on an open-book ICC exam or a Normal or Pekin license, plus boiler tenders and stationary engineers. Its four Contractor Business Licenses cover parking lot paving, sidewalks and driveways, right-of-way dumpsters and sewer connections, at $25.00 or $60.00 a year with $5,000 or $10,000 license and permit bonds. There is no general building contractor license.
Everywhere else. Every other Illinois city, village and county sets its own rules; many suburban villages register contractors and charge an annual fee, while others require only a permit and proof of insurance. Confirm the requirement, the current fee and the insurance limits with each building department before you bid work there.
- Chicago (Department of Buildings - General Contractor license, Classes A-E)
- Chicago (Department of Buildings - Trade Licensing index for the separate trade contractor licenses)
- Cook County (Department of Building and Zoning - contractor registration, unincorporated areas)
- Aurora (Division of Building and Permits - General contractor registration)
- Evanston (Building and Inspection Services - General Contractor registration)
- Joliet (Building and Inspectional Services - contractor registration, no fee)
- Rockford (Construction and Development Services - general contractors not licensed)
- Springfield (Building and Zoning Department - electrical and mechanical registrations only)
- Peoria (Contractor Business Licenses and Trade Licenses)
- Naperville (City of Naperville - Permits and Licenses)
Common questions
- Do I have to take the Oregon general contractor exam if I'm licensed in Illinois?
- The trade exam is waived, but Oregon requires a law or code exam.
- What does it cost to get a Oregon general contractor license from Illinois?
- Published fees on this path total $460, not counting exam vendor fees or bonds.
- Do my Illinois work hours count in Oregon?
- Yes. Documented out-of-state experience counts toward Oregon's eligibility requirements.
- How long does the application take?
- The board's published or typical processing time is about 42 days.
- Does it work the other way, from Oregon to Illinois?
- Not necessarily. Reciprocity is directed. Going from Oregon to Illinois, the mechanism is not applicable.
Sources
- NASCLA Accredited Examination for Commercial General Building Contractors · National Association of State Contractors Licensing Agencies · Other · verified September 17, 2026
- CCB Frequently Asked Questions (application), updated 3/2026 · Oregon Construction Contractors Board · Faq · verified September 17, 2026
- Construction Contractors Board - Continuing education · Oregon Construction Contractors Board · Agency Page · verified September 17, 2026
- CCB License Endorsements chart (11/2024) · Oregon Construction Contractors Board · Other · verified September 17, 2026
- Oregon Construction Contractors Board Examination Candidate Information Bulletin (PSI) · Oregon Construction Contractors Board / PSI Services LLC · Other · verified September 17, 2026
- Construction Contractors Board - How to get a CCB license (9 steps) · Oregon Construction Contractors Board · Agency Page · verified September 17, 2026
- CCB Sole Proprietorship License Application · Oregon Construction Contractors Board · Form · verified September 17, 2026
- Construction Contractors Board - Licensing (bonds, insurance, public works bond) · Oregon Construction Contractors Board · Agency Page · verified September 17, 2026
- OAR chapter 812, division 3 - Construction Contractors Board licensing · OAR 812-003-0131, 812-003-0142, 812-003-0152, 812-003-0153, 812-003-0260, 812-003-0265, 812-003-0270 · Oregon Secretary of State · Admin Rule · verified September 17, 2026
- OAR chapter 812, division 6 - Responsible Managing Individual, pre-licensure training, and testing · OAR 812-006-0100, 812-006-0110, 812-006-0150, 812-006-0160, 812-006-0300, 812-006-0310, 812-006-0450 · Oregon Secretary of State · Admin Rule · verified September 17, 2026
- OAR chapter 812, division 20 - Continuing education for construction contractors with commercial endorsements · OAR 812-020-0030 · Oregon Secretary of State · Admin Rule · verified September 17, 2026
- OAR 918-030-0015 - Contractor licenses (Building Codes Division requires a CCB license) · OAR 918-030-0015 · Oregon Secretary of State · Admin Rule · verified September 17, 2026
- ORS chapter 701 - Construction Contractors and Contracts (2025 edition) · ORS 701.005(16)-(17), 701.021, 701.042, 701.046, 701.050, 701.056, 701.063, 701.068, 701.073, 701.081, 701.084, 701.091, 701.098, 701.122 · Oregon Legislature · Statute · verified September 17, 2026
Verified dates are when a person last opened each source and confirmed the facts above. Cite the board, not us.