Illinois to New Mexico: residential contractor license reciprocity
Illinois does not issue a statewide residential contractor license, so there is nothing to transfer. Here is New Mexico's standard path for out-of-state applicants.
Your origin state does not issue a statewide license at this level, so there is no license to transfer. The destination's standard out-of-state path is shown; expect to meet it in full.
Reference only, not legal advice. Rules change; confirm with the licensing board before you apply. Full disclaimer.
Out-of-state residential contractor applying for GB-2 (all states)
Your out-of-state credentials give no advantage. You meet the destination's requirements from scratch.
A residential contractor licensed in another state gets no exam waiver and no shortened path to a New Mexico GB-2 license. The only reciprocity the Construction Industries Division publishes is for the EE-98J electrical journeyman certificate, 14.6.3 NMAC contains no endorsement or substantial-equivalence route for a contractor or Qualifying Party, and the NASCLA exam waiver that CID does operate is limited to the GB-98 and EE-98 classifications, not GB-2. What does carry across is the work itself: out-of-state experience counts in full toward the two years (4,000 hours) of foreman-level experience, provided it was gained while employed by a contractor licensed in the trade or was legal work in the state where it was performed, and the out-of-state contractor who signs the notarized affidavit attaches a copy of their own current state license. The applicant files the Qualifying Party application and General Building Work Experience Verification affidavits with PSI, waits for CID or PSI to approve the experience, then passes the GB-2 exam and the Business and Law exam, and the company that will hold the license applies separately with the bond, the tax registration certificate and proof of the Qualifying Party's exams. Statute does let the division enter reciprocal agreements with states having equivalent requirements, but none covering a building classification has been published.
Accredited college, university, manufacturer, vocational or apprenticeship training counts as one-half year of experience per year and may not exceed half of the two-year requirement. Estimating, project management, ordering supplies and supervising do not count as hands-on experience on the affidavit, and the affidavit must state whether the experience was residential or commercial. Once PSI approves the application, every remaining requirement must be met within six months or the fees are forfeited, and the trade exam and the Business and Law exam must both be passed within one year of each other. An exam may not be repeated more than twice in any 30-day period. Military service members, their spouses and dependent children and veterans who are currently licensed and in good standing in another jurisdiction with substantially equivalent requirements have a separate expedited route: CID issues within 30 days and waives the license fees for the first three years. A homeowner-scale exemption exists for an individual doing one project at a time for no more than $7,200 a year in casual or handyman work, but it does not extend to electrical, plumbing or gas fitting and requires an annual declaration to the division.
At a glance
- Trade exam
- Required
- Law / code exam
- Required
- Out-of-state hours
- Count toward eligibility
What you must already have
- You must document at least 4,000 hours of qualifying work experience.Two years (4,000 hours) of foreman-level practical or related trade experience in residential building, gained within the ten years immediately before application (14.6.6.9(B)(1) NMAC; NMSA 60-13-14(B)(8) as reduced by rule). It is documented on notarized General Building Work Experience Verification affidavits, one per employer or affiant, completed by an employer, supervisor, foreman or other contractor rather than by the applicant.
- Experience must have been gained while employed by a contractor licensed in the trade being applied for, or be work that was legal in the state where it was performed. An out-of-state contractor certifying the experience attaches a copy of their current state license to the affidavit; where the state does not license that trade, proof that the company was active and valid, such as a tax certificate or corporation papers, is attached instead.
- The Qualifying Party must be at least 18 and may qualify only one licensed entity unless there is at least thirty percent common ownership between the entities. CID may deny a license or certificate where the applicant or the proposed Qualifying Party has a disqualifying felony conviction, and an applicant denied on that basis may submit written evidence of mitigation or rehabilitation and appeal.
What you'll do to get licensed in New Mexico
- 1Application fee. Pay the application fee ($30). Non-refundable Qualifying Party application fee, paid to PSI with the notarized application and work-experience affidavits. Complete packets go to the PSI Albuquerque office by hand or mail; faxed and emailed forms are not accepted..
- 2Other. Qualifying Party certificate fee, charged for each classification on the application (14.5.5.14(A) NMAC). With the $30 application fee this is the $36 the Construction Industries Division quotes for a single-classification Qualifying Party filing. ($6).
- 3Trade exam. Pass the destination's trade exam. GB-2 Residential Building Contractor exam, administered by PSI once CID or PSI approves the experience affidavits: 80 questions, 225 minutes, open book, 75% (60 points) to pass. Content covers sitework, footings and foundations, concrete and reinforcement, masonry, carpentry, roofing, associated trades, general code, plan reading and estimating, and OSHA safety, against the 2021 New Mexico Residential Building Code (14.7.3 NMAC), the 2021 International Residential Code, the 2021 International Energy Conservation Code and 29 CFR 1926..
- 4Exam fee. Pay the exam fee ($134.53). PSI fee for the GB-2 exam, charged for a first attempt or a retake..
- 5Law / code exam. Pass a law, rules, or code exam. Contractor's Business and Law exam, required of all new Qualifying Party candidates: 50 questions, 130 minutes, open book, 75% (38 points) to pass, covering licensing requirements, estimating and bidding, business organization and financial management, tax and labor law, project management and lien law, contracts, risk management, and environment and safety. An approved Business and Law course taken with a CID-approved vendor may be completed in place of the exam..
- 6Exam fee. Pay the exam fee ($68.88). PSI fee for the Business and Law exam..
- 7Contractor license. Hold or obtain a contractor license ($30). Non-refundable contractor license application fee paid to PSI by the business, filed with the notarized Contractor License Application, a copy of the Qualifying Party's certificate or passing score reports, and the Business and Law score or course certificate. A $6 certificate fee covering the license certificate and two wallet cards is charged with it..
- 8License fee. Pay the license or certificate fee ($300). Classification fee for GB-2, covering the full three-year license term on PSI's current schedule. Adding a GS specialty classification alongside it does not raise the total above $300 for the category. Late renewal costs $1 a day for the first 30 days and the equivalent of one year's fee from 30 to 90 days; after 90 days the license is cancelled and the business must reapply..
- 9Surety bond. Post a surety bond ($10,000). $10,000 code bond from a corporate surety authorized to transact business in New Mexico, issued in the exact name shown on the application and effective for the entire three-year license period. It is the statutory proof of responsibility, may be drawn on only to cure division-certified code violations the licensee has not corrected, and must be kept in force for the whole term; claims are limited to two years after final inspection or issuance of a certificate of occupancy..
- 10Insurance. Carry the required insurance. Workers' compensation coverage is required of every licensed entity, and failure to maintain it is cause for revocation of the license. A sole proprietor with no employees may be exempt; the Workers' Compensation Administration can confirm. An application is placed on hold while the applicant is out of compliance..
- 11Business license. Obtain a business license. A registration certificate issued within the last twelve months by the New Mexico Taxation and Revenue Department in the exact name on the license application, plus proof of registration with the New Mexico Public Regulation Commission for a corporation or LLC, or with the Secretary of State for a limited liability partnership or limited partnership. A corporation, LLC, LP or LLP must be legally authorized to do business in New Mexico before the license issues, and the proposed business name must be cleared with PSI first..
- 12Background check. Complete a background check. CID reviews the application against the disqualifying felony convictions listed in 14.6.3.8(F) NMAC and may deny a license or certificate on that basis; sealed, dismissed, expunged or pardoned convictions and juvenile adjudications are not used. An application is also held where there are pending CID disciplinary actions, a workers' compensation compliance problem, a child support delinquency for the proposed Qualifying Party, or an open unlicensed-activity investigation..
Published fees on this path total $533.41, excluding exam-vendor fees, bonds, and insurance.
What you'll need to buy or arrange
Exam preparation
Most boards contract PSI, Prov, or ICC for exams. Check which code edition the exam is written to before buying a prep course.
- Trade exam
- Exam fee · $134.53
- Law / code exam
- Exam fee · $68.88
Surety bond
A license or contractor bond is bought from a surety, not the state. Price is a small percentage of the bond amount and depends on your credit.
- Surety bond · $10,000
Liability insurance
Some states require proof of general liability or workers' compensation coverage at licensing time.
- Insurance
Business registration
If you plan to contract in your own name, budget for a business license or entity registration on top of the trade license.
- Business license
How New Mexico licenses residential contractors
New Mexico residential contractor · “GB-2 Residential Building Contractor”
Statewide license
New Mexico licenses homebuilders statewide through the Construction Industries Division of the Regulation and Licensing Department, and the homes-only classification is GB-2 Residential: erect, alter, repair or demolish residences and apartment houses of not more than four family units in occupancy Groups R-1, R-2 and R-3, plus incidental Group U structures and any GS specialty work kept inside that residential scope. Anything commercial, and any residential building beyond four units, needs the GB-98 General Building classification instead. The license is held by a business, not by a person: CID issues it to a qualified entity that employs or is owned by a Qualifying Party, and the Qualifying Party is the individual who documents the experience, sits the exams and holds a personal, non-transferable certificate of qualification, so a builder moving to New Mexico applies first as a Qualifying Party and then for the company license. A GB-2 Qualifying Party needs two years (4,000 hours) of foreman-level practical or related trade experience gained within the ten years before applying, and must pass the GB-2 trade exam and the Contractor's Business and Law exam, or take an approved Business and Law course in place of that exam. Every licensed entity files a $10,000 code bond and carries workers' compensation coverage, and licenses run for three years. CID publishes reciprocity for one credential only, the EE-98J electrical journeyman certificate, so no other state's contractor license is recognized at this level.
Why Illinois has nothing to transfer
Illinois residential contractor · “No statewide license; local titles include Chicago General Contractor Class D or E and Chicago Home Repair”
Licensed by cities and counties
Illinois issues no statewide residential contractor, home builder or remodeler license, and no state agency examines or qualifies people who build or remodel houses. What the State does license is narrower and worth knowing: the Department of Financial and Professional Regulation licenses roofing contractors under the Illinois Roofing Industry Licensing Act, where a limited license covers residential properties of eight units or less and an unlimited license covers residential, commercial and industrial roofs, and a municipality or county may not issue a building permit to a roofing contractor without proof of that state license. IDFPR also licenses architects, professional and structural engineers, land surveyors and alarm contractors, and the Department of Public Health licenses plumbers, plumbing contractors and irrigation contractors, but nowhere on IDFPR's list of regulated professions is there a general, residential or building contractor. Everything else is local: Illinois municipalities are home rule units and license or register residential contractors one jurisdiction at a time, with the City of Chicago's General Contractor license by far the most consequential. A builder moving to Illinois therefore has no state license to transfer and no reciprocity to apply for; the practical work is registering in each city or county where they will pull permits, carrying the insurance each one demands, and obtaining the state roofing license if the company will do roofing. Statewide consumer law still applies: the Home Repair and Remodeling Act requires a written contract for any home repair or remodeling job over $1,000 and the "Home Repair: Know Your Consumer Rights" pamphlet on every job.
How local licensing works in Illinois
How it works in Illinois. There is no state license, no state application and no state exam for residential contractors. Each municipality decides who may pull a residential building permit, so a contractor must be licensed or registered separately in every jurisdiction where they build, and a credential from one Illinois city is not valid in the next. Almost all of these local programs are about identity, insurance, bonding and fees rather than trade competence, and none of them reviews or credits a residential contractor license held in another state. Roofing is the exception in the other direction: the State license is mandatory everywhere in Illinois, and cities from Rockford to Joliet to Cook County check it at the permit counter.
Chicago. This is the license that matters. 'A City of Chicago general contractor license is required to perform most types of building construction, alteration, repair, and demolition work within the City of Chicago', and it is needed to bid on, undertake, hire or supervise, or control the means and methods of work requiring a building, sign or demolition permit. Licenses are issued to businesses, including sole proprietorships, in five classes set by project value - the fair market value of materials and labor supplied by all contractors and subcontractors across all concurrent and consecutive work at the same site. The two classes a homebuilder or remodeler usually needs are Class D, capped at $4 million with ordinary demolition and $2 million per occurrence of insurance, at a $900.00 license and renewal fee, and Class E, capped at $500,000 with no demolition and $1 million per occurrence, at $300.00. There is no exam, no experience review and no qualifying party. The application asks for a statement of financial solvency in the format supplied, proof of authority to do business in Illinois (not required for sole proprietors), an Assumed Name Certificate from the County Clerk if a trade name is used, proof of insurance for the class from an insurer authorized in Illinois and rated B+ or better by A.M. Best, and government photo identification for the controlling persons. Continental Testing Services processes the application and renewal by mail for the Department of Buildings; the license runs one year and 'is automatically inactivated if the associated insurance policy expires.' Reinstatement costs $100.00 per year or part year expired.
Chicago, work that does not need a permit. A business that fixes, replaces, alters, modernizes, improves or adds to residential property but does not need a building permit takes a Home Repair license from Business Affairs and Consumer Protection instead: $1,000.00 for a two-year term, with a certificate of insurance of at least $300,000 per occurrence, and the rule that 'Home Repair licensees may not pull building permits.' A general contractor license replaces it - 'a home repair license is not required for a business that holds a General Contractor license', though a general contractor doing residential work must still follow the home repair consumer protection rules, which include a written estimate before work, a written invoice on completion, prior approval before exceeding the estimate, and the license number on contracts, advertisements and vehicles. Acquiring vacant land to build a new home, or renovating more than half of an existing building's floor area, requires a separate Residential Real Estate Developer license.
Cook County (unincorporated areas). 'All contractors performing work in unincorporated Cook County are required to register with the Cook County Department of Building and Zoning.' Registration costs $150 per trade initially and $75 per trade annually, due by December 31, and needs a $1,000,000 general liability certificate naming Cook County Building and Zoning at 69 W. Washington, Suite 2830, Chicago as certificate holder, filed by the owner or a corporate officer with the Articles of Incorporation or the current Annual Domestic Report. Roofing registrants must submit the State of Illinois roofing license and demolition registrants an approved bond. There is no exam. Homeowners who live on the property get 'General' contractor registration free of charge. Use the county's CookViewer tool first to check whether a site is actually unincorporated. Contact [email protected] or 312-603-0512.
Aurora. The Division of Building and Permits registers a General contractor for a $200 fee. The packet is the Contractor Licensing Application, a certificate of insurance naming the City of Aurora as primary and non-contributory additional insured with $1,000,000 general aggregate and $500,000 per occurrence, workers' compensation in compliance with Illinois statute, and proof the business is registered with the Secretary of State or a county DBA certificate. There is no test for the General category - Aurora's municipal testing applies only to electrical and mechanical contractors, who may use ICC certifications or a license from an accepted testing municipality instead. Roofing registration is also $200 and requires the state license, and workers' compensation cannot be replaced by an employee affidavit for roofers. Outstanding or expired permits will block a renewal. Submit to [email protected]; 77 S Broadway, (630) 256-3130.
Evanston. 'All contractors performing work within City limits are required to register with the City, including but not limited to General Contractors, Electrical, Carpentry, Concrete, Excavation, Masonry, Landscaping, Fence, Roofing and Sign contractors.' General Contractor registration is $150 and trade registration $125, both renewable annually through the Citizen Portal. Insurance must be general liability of at least $300,000 per occurrence, bodily injury of at least $100,000 per occurrence, property damage of at least $100,000 per occurrence and workers' compensation at statutory minimums, with Evanston as certificate holder; sole proprietors and partnerships with no employees may file an affidavit in place of workers' compensation, and right-of-way work needs $1,000,000 per occurrence naming the city as additional insured. State-regulated contractors submit a copy of the state license. An owner-occupant of a single-unit residence may act as their own general contractor.
Joliet. 'All contractors performing work within the City of Joliet must have current registration on file prior to permit issuance. There are no forms or fees for registration, unless you are a Sign Erector or for HVAC Testing.' Registration is a certificate of insurance naming the City of Joliet as certificate holder, with minimum limits of $250,000 bodily injury per person, $500,000 bodily injury per occurrence and $250,000 property damage per occurrence, emailed to [email protected]. Roofing needs the Illinois State Roofer's License, plumbing the Illinois Plumbing Contractor Registration, irrigation the state irrigation license, siding a Vinyl Siding Installers certificate, and electrical and HVAC a license from one of the municipalities Joliet accepts. Electrical, plumbing and HVAC contractors also file a project-specific Letter of Intent, and all subcontractors must be listed on the permit application.
Rockford. 'General contractors are not required to be licensed.' Rockford requires a building permit for any structure over 120 square feet that is constructed, altered, enlarged, repaired or moved, and for all roofing work, and notes that 'roofing contractors are required to obtain a license from the State of Illinois Department of Professional Regulation.' Tent erectors and outdoor sign contractors need annual city licenses.
Springfield. The Building and Zoning Department's published list of applications contains electrical and mechanical contractor registrations and licenses and nothing else for contractors - there is no general contractor or home improvement registration. The city's building permit application collects the general contractor's name and address but asks for a license number only on the roofing line. Building and Zoning is at 300 South 7th Street, Room 304, (217) 789-2171.
Peoria. Peoria's Contractor Business Licenses cover only four activities - parking lot paving, sidewalk and driveway work, placing a dumpster or storage unit in the right-of-way, and sewer connections - at $25.00 or $60.00 a year with license and permit bonds of $5,000 or $10,000. Its trade licenses cover electrical and HVAC contractors at $150.00 each, issued to individuals rather than businesses and requiring an open-book ICC exam unless the applicant holds a Normal or Pekin license, plus boiler tender and stationary engineer licenses. There is no general building contractor or residential builder license in Peoria.
Everywhere else. Other Illinois municipalities set their own rules and most of them register rather than license residential builders. Ask the building or development services department of each city, village or county before contracting there, and confirm the current fee and insurance limits before buying coverage, because these are set locally and change independently.
- Chicago (Department of Buildings - General Contractor license, Classes A-E)
- Chicago (Business Affairs and Consumer Protection - Home Repair business license)
- Cook County (Department of Building and Zoning - contractor registration, unincorporated areas)
- Aurora (Division of Building and Permits - General contractor registration)
- Evanston (Building and Inspection Services - General Contractor registration)
- Joliet (Building and Inspectional Services - contractor registration, no fee)
- Rockford (Construction and Development Services - general contractors not licensed)
- Springfield (Building and Zoning Department - electrical and mechanical registrations only)
- Peoria (Contractor Business Licenses and Trade Licenses)
- Naperville (City of Naperville - Permits and Licenses)
Common questions
- Do I have to take the New Mexico residential contractor exam if I'm licensed in Illinois?
- Yes. New Mexico requires the trade exam on this path, plus a law or code exam.
- What does it cost to get a New Mexico residential contractor license from Illinois?
- Published fees on this path total $533.41, not counting exam vendor fees or bonds.
- Do my Illinois work hours count in New Mexico?
- Yes. Documented out-of-state experience counts toward New Mexico's eligibility requirements.
- Does it work the other way, from New Mexico to Illinois?
- Not necessarily. Reciprocity is directed. Going from New Mexico to Illinois, the mechanism is not applicable.
Sources
- Construction Industries Licensing Act, NMSA 1978 Chapter 60, Article 13 (RLD compilation as of July 1, 2021) · NMSA 1978 §§ 60-13-3, 60-13-14, 60-13-14.1, 60-13-23, 60-13-49 · New Mexico Regulation and Licensing Department · Statute · verified September 17, 2026
- 14.5.5 NMAC - Construction Industries General Provisions: Fees · 14.5.5.8 and 14.5.5.14 NMAC · New Mexico Commission of Public Records, State Records Center and Archives · Admin Rule · verified September 17, 2026
- 14.6.3 NMAC - Construction Industries Licensing: Contractor's License Requirements · 14.6.3.8 NMAC · New Mexico Commission of Public Records, State Records Center and Archives · Admin Rule · verified September 17, 2026
- 14.6.6 NMAC - Construction Industries Licensing: Classifications and Scopes of Work · 14.6.6.8 and 14.6.6.9 NMAC · New Mexico Commission of Public Records, State Records Center and Archives · Admin Rule · verified September 17, 2026
- NM CID - How to Obtain a Contractor License and Contractor License Application (updated October 2023) · PSI Services for the New Mexico Construction Industries Division · Form · verified September 17, 2026
- State of New Mexico Contractor (Qualifying Party) Examinations Candidate Information Bulletin (PSI) · PSI Services for the NM Construction Industries Division · Other · verified September 17, 2026
- New Mexico Contractor Licensing - Frequently Asked Questions (CID / PSI) · PSI Services for the New Mexico Construction Industries Division · Faq · verified September 17, 2026
- PSI General Building Work Experience Verification - New Mexico Contractor Licensing Service · PSI Services for the New Mexico Construction Industries Division · Form · verified September 17, 2026
- New Mexico Licensing Fees (CID contractor, qualifying party and journeyman fee schedule) · PSI Services for the New Mexico Construction Industries Division · Other · verified September 17, 2026
- NM CID Qualifying Party Certificate Application and Instructions (instructions updated May 2025, form updated August 2025) · PSI Services for the New Mexico Construction Industries Division · Form · verified September 17, 2026
- NM Regulation and Licensing Department - Apply for a Construction Industries License · New Mexico Regulation and Licensing Department, Construction Industries Division · Agency Page · verified September 17, 2026
Verified dates are when a person last opened each source and confirmed the facts above. Cite the board, not us.