LicensebyState

Ohio to Washington: residential contractor license reciprocity

No credit· Start overVerified September 17, 2026· 15 sources

Ohio does not issue a statewide residential contractor license, so there is nothing to transfer. Here is Washington's standard path for out-of-state applicants.

Your origin state does not issue a statewide license at this level, so there is no license to transfer. The destination's standard out-of-state path is shown; expect to meet it in full.

Reference only, not legal advice. Rules change; confirm with the licensing board before you apply. Full disclaimer.

Everyone registers the same way; an out-of-state contractor license transfers nothing

Your out-of-state credentials give no advantage. You meet the destination's requirements from scratch.

A residential contractor licensed in another state registers in Washington exactly as a first-time applicant does, and holding that license neither helps nor hinders the application. L&I does not review, verify or credit out-of-state credentials for contractor registration, and it cannot waive anything, because there is nothing to waive: Washington's Contractor Registration Act and its rules impose no examination, no experience requirement and no competency test, and neither the statute, the rules nor the application form mentions reciprocity or another state's license. Washington also does not participate in the NASCLA Accredited Examination program, since it holds no contractor examination for that examination to replace. The steps are the same for an applicant from Idaho, from Florida or from down the street: file a Business License Application with the Department of Revenue for a UBI number (and file with the Secretary of State first if the business is a corporation, LLP or LLC), buy a continuous contractor surety bond of $30,000 for a general registration or $15,000 for a specialty registration, or assign a savings account for the same amount, buy general liability insurance naming L&I as certificate holder, complete and notarize the Application for Construction Contractor Registration (F625-001-000) with a notarized affidavit from every principal, and pay $150.20. The bond, the insurance certificate and the application must all carry the exact business name registered with the Department of Revenue. Registration lasts two years and renews for $150.20.

The 3-4 week figure is L&I's published processing time for applications sent by mail; applications completed in person at a local L&I office are handled at the counter, and the registration card follows in about two weeks either way. The only out-of-state accommodation anywhere in the registration statute is unrelated to skills: RCW 18.27.030(1)(c)(iii) lets an applicant domiciled in a state or Canadian province covered by an extraterritorial workers' compensation agreement file that jurisdiction's certificate of coverage instead of opening a Washington industrial insurance account. L&I's out-of-state specialists can be reached at [email protected] or 360-902-4817. Registration does not cover the licensed trades: a contractor whose crews do plumbing, electrical, elevator, boiler, asbestos or mobile home installation work needs the separate trade license or certification for that work as well.

At a glance

Trade exam
Waived
Law / code exam
Not required
Out-of-state hours
Do not count
Typical processing
About 28 days

What you must already have

  • Every owner, member, partner and corporate officer must be at least 18 and provide a Social Security number or individual taxpayer identification number, a government-issued photo ID number and a residential address, and must sign the application before a notary public.RCW 18.27.030(1)(a) and (g); the age and notarization requirements are stated in the instructions to form F625-001-000. Falsifying the application carries a fine of up to $10,000 and can lead L&I to deny or revoke the registration.
  • The application is denied if a principal has an unsatisfied final judgment for work subject to chapter 18.27 RCW, or owes certain unpaid debts to L&I, or if the business is a successor to a previously registered entity with such a judgment or debt. The application asks whether the applicant, a spouse or registered domestic partner, or anyone with common ownership, management or control has ever been registered as a contractor in Washington.
  • Washington asks for no trade experience, apprenticeship hours, education or examination result, so documented years of homebuilding in another state neither shorten nor replace any step.

What you'll do to get licensed in Washington

  1. 1Application fee. Pay the application fee ($150.20). Contractor registration issuance fee (WAC 296-200A-900(1)). The registration is valid for two years from issuance and renews for the same $150.20; reinstatement after a suspension costs $70.90 and a duplicate registration certificate costs $16.50. Pay by check or money order if applying by mail, or by cash, check, money order or credit or debit card in person at a local L&I office..
  2. 2Surety bond. Post a surety bond ($30,000). Continuous Contractor's Surety Bond (F625-003-000) naming the State of Washington as obligee, issued by a surety insurer authorized under chapter 48.28 RCW: $30,000 for a general contractor registration, or $15,000 if you register in a single specialty trade. The original signed and sealed bond must be filed with L&I, or the surety may file it through L&I's electronic bond and insurance policy system. An assigned savings account, certificate of deposit, time deposit or money market account at a bank, savings and loan or credit union with a Washington branch (form F625-008-000) may be posted instead. The amount steps up for a contractor with final judgments involving a residential single-family dwelling in the previous five years: for a general registration $40,000 after one judgment, $60,000 after two and $90,000 after three or more (specialty registrations $20,000, $30,000 and $45,000). Cancellation of the bond automatically suspends the registration..
  3. 3Insurance. Carry the required insurance ($250,000). General liability insurance of $200,000 public liability and $50,000 property damage, or a $250,000 combined single limit policy, written in the exact business name with L&I named as certificate holder. The original certificate must reach L&I by mail, through the designated insurance agent portal or in person at a service location; L&I does not accept certificates by email or fax. An assigned account in the statutory amounts may be filed instead as proof of financial responsibility (RCW 18.27.050(3)). Cancellation or expiry of the policy automatically suspends the registration..
  4. 4Business license. Obtain a business license. A Washington Business License Application filed with the Department of Revenue Business Licensing Service, producing the nine-digit Uniform Business Identifier (UBI) that goes on the contractor registration application; the UBI must stay active and valid for as long as the registration is held. A corporation, limited partnership, LLP or LLC, including one formed in another state, files with the Secretary of State first. L&I will not process the registration until it confirms that the business license application has been filed and an excise tax account is open. The Department of Revenue's application fee varies with the endorsements the business needs and is not published as a single figure; see dor.wa.gov for the current processing fee..
  5. 5Other. Notarized Application for Construction Contractor Registration (F625-001-000), with an individually notarized affidavit of signature from each owner, member, partner and corporate officer. Signatures must be original, so L&I cannot accept a copy or an emailed application; it is filed in person at a local L&I office or mailed to Contractor Registration, PO Box 44450, Olympia WA 98504-4450 together with the bond, the insurance certificate and the fee..
  6. 6Other. Workers' compensation coverage and an employment security department number if the business will have employees, opened through the Department of Revenue; a business with no Washington employees may substitute its UBI account number. An applicant domiciled in a state or Canadian province with an extraterritorial coverage agreement may instead file that jurisdiction's certificate of workers' compensation coverage (RCW 18.27.030(1)(c)(iii)). An employer identification number is needed from the IRS unless the applicant is a sole proprietor with no employees..
  7. 7Other. Model Disclosure Statement, Notice to Customer (F625-030-000), which the contractor must give the customer on every residential job of $1,000 or more and on commercial projects of $1,000 to $60,000. The registration number must also appear on all business communications, including business cards, advertising, estimates and bid proposals..
  8. 8Other. Separate trade licensing where the work calls for it. Contractor registration does not authorize plumbing, electrical, elevator, boiler, asbestos or mobile home installation work; each of those carries its own education, examination and licensing requirements under its own chapter, and electrical work is licensed under chapter 19.28 RCW rather than as a registration specialty. Lead-based paint work in pre-1978 housing is administered by the Washington State Department of Commerce and pesticide application by the Washington State Department of Agriculture. (if applicable).

Published fees on this path total $150.20, excluding exam-vendor fees, bonds, and insurance.

What you'll need to buy or arrange

Surety bond

A license or contractor bond is bought from a surety, not the state. Price is a small percentage of the bond amount and depends on your credit.

  • Surety bond · $30,000

Liability insurance

Some states require proof of general liability or workers' compensation coverage at licensing time.

  • Insurance · $250,000

Business registration

If you plan to contract in your own name, budget for a business license or entity registration on top of the trade license.

  • Business license

How Washington licenses residential contractors

Washington residential contractor · “General Contractor Registration (or a Specialty Contractor Registration)

Statewide license

Verified September 17, 2026· 7 sources

Issued by Washington State Department of Labor & Industries, Contractor Registration

Washington does not license residential building contractors. It registers every construction contractor with the Department of Labor & Industries, and registration is the only credential a homebuilder or remodeler needs: there is no trade examination, no business-and-law examination, no experience or apprenticeship requirement, no financial statement and no named qualifying party anywhere in chapter 18.27 RCW or chapter 296-200A WAC. The same registration covers houses and commercial buildings, because Washington's two classifications divide work by the number of trades rather than by market. A General contractor registration is for a business whose work uses more than one building trade on a single job or under a single building permit, and it covers residential and commercial work alike; a Specialty contractor registration limits the business to one of 63 named trades such as roofing, framing and rough carpentry, siding, drywall or HVAC. L&I's own application makes the point explicitly: it asks whether you will do commercial, residential or both, then says the question is 'for statistical reasons and you will not be held to the type you choose.' A developer who subdivides land for residential purposes or builds one or more residential units needs the general registration, and there is no separate homebuilder, residential builder or home improvement credential above or below it. The registration belongs to the business rather than to a person, so a builder moving to Washington registers the sole proprietorship, partnership, corporation or LLC that will sign contracts; every owner, member, partner and corporate officer signs the application before a notary and provides a Social Security number or ITIN, and each must be at least 18. What Washington requires instead of qualifications is financial protection for the customer: a Uniform Business Identifier from the Department of Revenue, a continuous $30,000 surety bond for a general registration or $15,000 for a specialty registration, general liability insurance of $200,000 public liability and $50,000 property damage or $250,000 combined single limit, and a $150.20 fee for a two-year registration.

Moving to WashingtonLeaving Washington

Why Ohio has nothing to transfer

Ohio residential contractor · “Home improvement / remodeling contractor license or registration (city-issued)

Licensed by cities and counties

Verified September 17, 2026· 22 sources

Issued by No state authority; cities and counties license and register residential contractors

Ohio issues no statewide residential building, home builder or home improvement contractor license. The Ohio Construction Industry Licensing Board (OCILB), in the Department of Commerce, licenses individual contractors in five commercial trades only - electrical, HVAC, refrigeration, plumbing and hydronics - and its own page states that "all local building and health departments regulate residential contractors"; the Department of Commerce says plainly that "while residential contractors are not required to be licensed by the state, local building departments throughout Ohio may have their own verification or licensing requirements." Housing work is therefore licensed or registered jurisdiction by jurisdiction, and the rules vary a great deal: Columbus and Toledo run real competency licenses built on the ICC Ohio home improvement and building contractor examination (exam ID 767-OH-GC), documented experience and a board hearing, while Cleveland, Cincinnati and Akron require registration backed by insurance, bonding or workers' compensation but no exam, and Dayton registers only the trades. A remodeler moving to Ohio has no state license to transfer and no state reciprocity to apply for, so the practical work is qualifying or registering in each place where they pull permits and carrying the insurance each one demands. The credential that actually travels is the ICC contractor examination rather than another state's license. Anyone who self-performs electrical, HVAC, refrigeration, plumbing or hydronics work still needs the matching OCILB state license, and Ohio's only statewide residential construction statute, R.C. Chapter 4722, governs written contracts and down payments on home construction service contracts over $25,000 rather than licensing anyone.

How local licensing works in Ohio

How local licensing works. Ohio has roughly 800 certified building departments, and each city, county or township decides for itself whether residential contractors are licensed, registered or left alone. A credential from one Ohio jurisdiction does not carry into the next one, and none of the jurisdictions below grants anything for a license held in another state. Use the Board of Building Standards jurisdiction map at com.ohio.gov/JurisdictionMap to find out which department has authority over a given address before applying anywhere.

Columbus. Building and Zoning Services licenses residential work under Chapter 4114 of the Columbus Building Code. A Home Improvement General Contractor license covers structural work on existing one-, two- and three-family dwellings and their accessory structures. It requires "a score of 70% or higher for 767 Ohio Home Improvement Contractor" (the ICC exam, booked through the International Code Council on (877) 783-3926), a "minimum of three (3) full years of hands-on experience in the one (1), two (2), and three (3) family home improvement field", and approval by the Board of Review of General and Home Improvement Contractors, which meets on the first Wednesday of each month and needs the notarized application at least seven days beforehand. A Home Improvement Limited Contractor license covers roofing, siding, decking, waterproofing, fencing, driveway approaches and similar specialized work and requires one full year of hands-on experience in that field plus board approval. A builder putting up new houses registers instead as a General Contractor, which covers "all permits to build new 1, 2, or 3 family, multi-family (4 or more dwelling units), and commercial structures" and needs a $25,000 bond on the city's bond form and liability insurance of at least $300,000 for damages to a single person and $500,000 per occurrence, with no exam. The 2026 fee schedule sets a $300 application fee for the board-reviewed licenses (including Home Improvement Contractor and HIC-Limited) and a $350 annual license and registration fee; a change of assignment is $100. Registrations expire at the end of the twelfth month from issuance. Building and Zoning Services, 111 North Front Street, (614) 645-7433, [email protected].

Toledo. The Division of Building Inspection licenses "contractors engaged in the business of making improvements to residential structures regulated by the Residential Code of Ohio" under Toledo Municipal Code Chapter 1313, in two tiers. A Certified Remodeling Contractor "may engage in all residential construction, alterations and renovations" and must first pass the ICC Building Contractor C examination (exam ID 767-OH-GC, delivered by Pearson VUE, nearest center in Maumee) and then the City of Toledo Certified Remodeling Exam covering Chapters 11 and 13 of the Municipal Code. A Limited Remodeling Contractor is "restricted to residential improvements such as roof and window replacement, siding application, installation of insulation, fencing, and swimming pools greater than 24 inches in depth" and sits only the city exam, which covers Chapter 13 and the 2024 International Residential Code. Both exams are open book. Applications go first to the city's Board of Control for Home Improvement and Remodeling Contractors, which decides whether the applicant may test, and the applicant must document one of four qualifications: a two-year degree in construction management, architecture or engineering; a licensed journeyman certificate in a construction trade; five years working in general building construction under a licensed remodeler, homebuilder or general contractor, evidenced by a notarized employer statement and five years of tax records; or five years self-employed on construction projects, evidenced by a notarized resume and five years of tax records. Three unrelated references and a full employment history are filed with the application. The fee is $200, of which $175 is refunded if the Board of Control finds the applicant unqualified to test. After passing, a Certificate of Compliance from the Division of Taxation is required before the license issues, and holders must carry liability insurance "in the amount of $100,000 to $300,000." Licenses renew annually and expire December 31; ten hours of continuing education are required each year. One Government Center, Suite 1600, 419-245-1220.

Cleveland. The Department of Building & Housing states that "to build or rehabilitate Cleveland homes, contractors must be bonded, insured, and registered", and that "contractors must be registered with the City of Cleveland within their trade in order to obtain permits. Separate permits are required for each separate trade, i.e. general, plumbing, HVAC, electrical, and elevator." Registration runs under Chapter 3107 of the Codified Ordinances, Registration of Contractors, which provides for both a Certificate of Registration and a Limited Certificate of Registration and sets separate qualifications for each. The city publishes a General Contractor Registration Application package in the Contractor Packages section of its construction permitting resources page; the bond amount, insurance limits and fee are set out in that package and in Chapter 3107 rather than on the department's web pages, so confirm them with Building & Housing on 216-664-2910 before filing. Registration status can be checked on 216-664-2884. Electrical, plumbing and HVAC contractors must hold the OCILB state license before the city will register them.

Cincinnati. The Department of Buildings & Inspections registers contractors under Chapter 1106 of the Municipal Code in three classes, two of which reach housing. A Home Improvement Contractor registration covers "all contractors that are involved in repair, remodeling, alteration, improvement, or addition to any building used as a private residence in one, two and three family structures." A Building Construction Contractor registration covers everything else, and expressly "include[s] contractors that engage in the construction of new one, two and three family dwellings" as well as specialties such as demolition, carpentry, masonry and glazing. The filing is the signed application, a certificate of liability insurance from an Ohio-licensed insurer with "minimum liability limits of one hundred thousand dollars ($100,000) for damages to a single person, and three hundred thousand dollars ($300,000) for one (1) occurrence", proof of Ohio workers' compensation, an assignment form naming everyone allowed to sign permit applications, and a federal tax ID or Social Security number. The fee is $125.00 plus a 3% technology surcharge, a 1% financial recovery fee and a 1% training surcharge, a total of $131.25 a year, and a registration may be bought for up to three years; same-day processing costs $208 more and mid-term changes $78. There is no exam, experience or bond requirement. An owner of a one-, two- or three-family dwelling is exempt where they personally perform the work and will occupy the home for at least a year. Working unregistered draws a $750 citation for a first offense. 805 Central Avenue, Suite 500, (513) 352-3271.

Akron and Summit County. Akron's rule is short: "the City of Akron requires all contractors regardless of trade to register as a contractor if the work they are performing requires a permit to do the work." The filing is the contractor registration application, an Akron Tax Registration Number, a certificate of liability insurance, any state licenses the trade requires, and proof of workers' compensation unless there are no employees. There is no exam and no published registration fee. The building permits themselves come from the Summit County Department of Building Standards, which in March 2024 replaced annual contractor registration with a permit-based process: "the $135 annual fee for contractors and the requirement for a $10,000 bond are now eliminated", though "contractors will still be required to provide liability insurance, State license if applicable, and a Tax ID Number." The same code change requires that property owners working on homes they do not and will not occupy have a qualified contractor take responsibility for the installations. Akron Plans & Permits, 1030 E. Tallmadge Ave., 330-375-2010; registration questions 330-375-2037. Summit County Building Standards, same address, 330-630-7280.

Dayton. The Division of Building Inspection publishes registration and bond forms only for electrical, plumbing, warm air heating and pipe-laying contractors, with separate plumbing journeyman and apprentice forms. There is no Dayton registration for a remodeler or a homebuilder as such; a residential builder pulls permits and hires or employs the registered trades. Building Inspection, 937-333-3979; One Stop Center, 371 West Second Street, second floor, 937-333-3883.

Cuyahoga County. The county created a Division of Building Standards in 2025 "with the mission of improving compliance with State of Ohio Board of Building Standards for both residential and commercial/non-residential construction within the County." It will provide contractor registration, plan review, permitting and inspections for partner communities, with registration "completed through a secure online portal" on its website; the partner community list is still being announced and an approved fee schedule is due by December 1, 2026. The county notes that it "does not offer formal endorsement, evaluation, or recommendation of any contractors or construction services" and directs residents to the state's building department look-up tool for their address. [email protected].

Everywhere else. The remaining hundreds of Ohio municipalities, townships and county building departments each set their own rules, from a full licensing board to nothing beyond a permit and proof of insurance. Identify the department with jurisdiction over the address first, then ask what it registers. Whatever the local answer, the statewide obligations are the same: an OCILB license for any self-performed electrical, HVAC, refrigeration, plumbing or hydronics work, and a written contract meeting R.C. Chapter 4722 for any home construction service contract over $25,000.

Moving to OhioLeaving Ohio

Common questions

Do I have to take the Washington residential contractor exam if I'm licensed in Ohio?
No. The trade exam is waived on this path.
What does it cost to get a Washington residential contractor license from Ohio?
Published fees on this path total $150.20, not counting exam vendor fees or bonds.
Do my Ohio work hours count in Washington?
No. Washington does not credit out-of-state hours on this path.
How long does the application take?
The board's published or typical processing time is about 28 days.
Does it work the other way, from Washington to Ohio?
Not necessarily. Reciprocity is directed. Going from Washington to Ohio, the mechanism is not applicable.

Sources

  1. NASCLA Accredited Examination for Commercial General Building Contractors · National Association of State Contractors Licensing Agencies · Other · verified September 17, 2026
  2. NASCLA Commercial Exam - Participating State Agencies · National Association of State Contractors Licensing Agencies · Other · verified September 17, 2026
  3. Washington Department of Revenue - Apply for a business license (UBI number) · Washington State Department of Revenue, Business Licensing Service · Agency Page · verified September 17, 2026
  4. L&I Form F625-001-000 - Application for Construction Contractor Registration (rev. 07-2026) · Washington State Department of Labor & Industries · Form · verified September 17, 2026
  5. L&I - Register as a Contractor · Washington State Department of Labor & Industries · Agency Page · verified September 17, 2026
  6. RCW 18.27.010 - Definitions (contractor, general contractor, specialty contractor) · RCW 18.27.010 · Washington State Legislature · Statute · verified September 17, 2026
  7. RCW 18.27.030 - Application for registration - Grounds for denial and suspension · RCW 18.27.030 · Washington State Legislature · Statute · verified September 17, 2026
  8. RCW 18.27.040 - Bond or other security required · RCW 18.27.040 · Washington State Legislature · Statute · verified September 17, 2026
  9. RCW 18.27.050 - Insurance or financial responsibility required · RCW 18.27.050 · Washington State Legislature · Statute · verified September 17, 2026
  10. RCW 18.27.060 - Certificate of registration - Issuance, duration, renewal - Suspension · RCW 18.27.060 · Washington State Legislature · Statute · verified September 17, 2026
  11. Chapter 18.27 RCW - Registration of Contractors (full chapter text) · Chapter 18.27 RCW · Washington State Legislature · Statute · verified September 17, 2026
  12. WAC 296-200A-016 - Definitions of the specialty contractor classifications for the purpose of contractor registration only · WAC 296-200A-016; WAC 296-200A-015 · Washington State Legislature · Admin Rule · verified September 17, 2026
  13. WAC 296-200A-025 - How does a contractor register, renew, reregister or reinstate its registration? · WAC 296-200A-025 · Washington State Legislature · Admin Rule · verified September 17, 2026
  14. WAC 296-200A-030 - How much are the surety bond or savings account amounts? · WAC 296-200A-030 · Washington State Legislature · Admin Rule · verified September 17, 2026
  15. WAC 296-200A-900 - What fees does the department charge contractors for issuance, renewal, reregistration, and reinstatement of certificates of registration? · WAC 296-200A-900 · Washington State Legislature · Admin Rule · verified September 17, 2026

Verified dates are when a person last opened each source and confirmed the facts above. Cite the board, not us.

Report an error on this page

Related