LicensebyState

Texas to Alaska: residential contractor license reciprocity

No credit· Start overVerified September 17, 2026· 12 sources

Texas does not issue a statewide residential contractor license, so there is nothing to transfer. Here is Alaska's standard path for out-of-state applicants.

Your origin state does not issue a statewide license at this level, so there is no license to transfer. The destination's standard out-of-state path is shown; expect to meet it in full.

Reference only, not legal advice. Rules change; confirm with the licensing board before you apply. Full disclaimer.

Registration and residential endorsement earned from scratch (every state)

Your out-of-state credentials give no advantage. You meet the destination's requirements from scratch.

A builder arriving in Alaska with a contractor license from another state gets no credit for it. Alaska's contractor law, AS 08.18 and 12 AAC 21, contains no reciprocity provision, no endorsement of out-of-state credentials and no examination waiver, the division publishes no verification-of-licensure form, and Alaska is not one of the states that accepts the NASCLA Accredited Examination in place of its own. Every applicant follows the same two steps: the business registers as a General Contractor with Residential Endorsement with its bond, insurance and fees, and the person who will hold the endorsement completes the 16-hour cold climate course and passes the Alaska residential contractor endorsement examination through PSI. That examination is open-reference, 100 questions in 240 minutes with 70 percent to pass, and it is built around arctic structural and thermal construction, so it tests material that a license from a warmer state will not have covered. The division does not require board approval to sit the examination and does not publish a processing time; it says an application generally takes several weeks once the complete packet is in.

12 AAC 21.680(3) accepts a passing score on the PSI residential contractor endorsement examination 'or other examination approved by the department', and AS 08.18.025(b)(4) accepts the Alaska craftsman home program 'or its equivalent' or a postsecondary course in arctic engineering 'or its equivalent'. Neither the division's website nor its forms name any other approved examination or any specific equivalent course beyond the three providers listed on Form 08-4161, so an applicant holding an out-of-state residential builder credential or a cold-climate building course from elsewhere should write to [email protected] or call (907) 465-2050 and ask whether it will be accepted before paying PSI. Alaska sets no minimum trade experience or apprenticeship hours for a contractor registration at any tier, so documented out-of-state years shorten nothing.

At a glance

Trade exam
Required
Law / code exam
Not required
Out-of-state hours
Do not count

What you must already have

  • Your qualifying exam must have been passed within the last 1 year.AS 08.18.025(b)(3) and 12 AAC 21.680(3). PSI also states that examination results are valid for one year. If the endorsement later lapses for more than two years the examination must be passed again, and after five years a completely new application is required (12 AAC 21.695).
  • You must have no disciplinary action or unresolved complaints on your record.
  • The endorsement is held by a person and assigned to a registered general contractor. The holder must be the sole proprietor, one of the partners, an employee, authorized board member or officer of the corporation, or an employee or authorized member of the LLC, and may be assigned to no more than two general contractors.12 AAC 21.690. If the general contractor the endorsement is assigned to fails to renew or is deactivated, the division reissues the endorsement as unassigned and the holder may reassign it to another registered general contractor on the division's assignment form (#08-4465).
  • Alaska sets no minimum trade experience, apprenticeship or supervisory hours for a contractor registration or for the residential contractor endorsement. Nothing in the application asks how long the applicant has worked in construction.

What you'll do to get licensed in Alaska

  1. 1Trade exam. Pass the destination's trade exam. Alaska Residential Contractor Endorsement Examination, administered by PSI Services LLC: 100 questions, 240 minutes, 70 percent to pass. It is open reference, so code books and the Alaska Centralized Regulations may be brought into the test center along with a silent nonprinting calculator. Content runs from sitework, foundations, concrete, masonry, plan reading and carpentry to advanced cold climate home building techniques, American Wood Council framing fundamentals, seismic and wind loading, OSHA safety and the Alaska regulations for the residential endorsement. Division approval is not needed to sit it; the candidate registers with PSI directly and files the passing result with the endorsement application..
  2. 2Other. Proof of satisfactory completion, within the two years before the endorsement application, of the Alaska craftsman home program or its equivalent, or a postsecondary course in arctic engineering or its equivalent. The program page describes this as a 16-hour cold climate course. Form 08-4161 lists the providers the division has on record: At Your Pace Online LLC, Alaska Craftsman Home Program Inc and Wisdom and Associates Inc..
  3. 3Exam fee. Pay the exam fee ($150). $150 examination fee paid to PSI Services LLC when the examination is booked. It is nonrefundable and nontransferable and stays valid for one year from the date of payment. An examination review, if requested after a failure, costs a further $150 and lasts one hour. The figure comes from the candidate bulletin the division publishes, which is the 2017 edition, so confirm the current amount with PSI on (800) 733-9267 before paying..
  4. 4Application fee. Pay the application fee ($100). $100 nonrefundable application fee. It is charged twice on this route: once on the General Contractor with Residential Endorsement registration application (#08-4819) and once on the Contractor Residential Endorsement application (#08-4161), because the registration and the endorsement are separate filings. The fee is never refunded, including where an application is abandoned after 12 months without correspondence..
  5. 5License fee. Pay the license or certificate fee ($250). $250 registration fee, also charged separately on the registration and on the endorsement, making $350 due with each of the two applications. Construction contractor registrations and residential endorsements run on a two-year cycle and expire on September 30 of even-numbered years whatever date they were issued, except that one issued within 90 days of an expiration date runs to the next cycle..
  6. 6Surety bond. Post a surety bond ($20,000). $20,000 surety bond for a general contractor with a residential contractor endorsement who performs exclusively residential work; a general contractor who also takes commercial work posts $25,000. The bond runs to the State, covers taxes, labor and material claims and judgments for negligent or improper work, and must remain in effect for three years until canceled by the surety, the principal or the department. A cashier's check cash deposit, a time certificate of deposit or a savings passbook held in trust for the State may be filed instead, using the division's Assignment of Cash Deposit form. The bond document must reach the division within 30 days of issuance and must carry the business name exactly as it appears on the application, including any DBA..
  7. 7Insurance. Carry the required insurance. Public liability and property damage insurance covering Alaska contracting operations, with limits of at least $20,000 for damage to property, $50,000 for injury including death to any one person and $100,000 for injury including death to more than one person (AS 08.18.101). Workers' compensation coverage from a carrier admitted in Alaska, or a self-insurance certificate, is also required if the business uses employee labor or is a corporation or LLC. Like the bond, the certificate must reach the division within 30 days of issuance with the business name written exactly as on the application..
  8. 8Business license. Obtain a business license. A corporation, LLC or other registered entity must be on file with the division's Corporations Section, with its Alaska entity number on the application, before the contractor application is processed. A State of Alaska business license under AS 43.70 is obtained after the professional registration is issued; the registration does not take its place, and the DBA name on the two must match. All advertising, contracts and signage must then carry the contractor's registered name, registration number, mailing address and physical address, or direct customers to a website that carries them (AS 08.18.051)..
  9. 9Continuing education. Complete continuing education. A renewal condition rather than an entry requirement: a residential contractor endorsement holder documents 16 contact hours of approved continuing competency activity each licensing period. At a first renewal it is eight hours for each complete calendar year the endorsement was held, and nothing at all if it was held for less than a full calendar year. No more than eight hours may come from business topics such as management, marketing, finance, safety, CPR and first aid; up to 16 may come from technical topics such as construction codes, materials and energy, remodeling and construction techniques. The division audits a share of renewals, so certificates should be kept..
  10. 10Other. With the endorsement application: a notarized signature, an Authorization for Release of Records form (#08-4161a), the name and registration number of the licensed general contractor the endorsement will be assigned to, and a copy of the official PSI examination result. A United States Social Security number must be on file before any professional license is issued, or a signed exemption request form in its place..

Published fees on this path total $500, excluding exam-vendor fees, bonds, and insurance.

What you'll need to buy or arrange

Exam preparation

Most boards contract PSI, Prov, or ICC for exams. Check which code edition the exam is written to before buying a prep course.

  • Trade exam
  • Exam fee · $150

Continuing education

Renewals usually need approved CE hours, often on the latest NEC. Reciprocal licensees are rarely exempt.

  • Other
  • Continuing education

Surety bond

A license or contractor bond is bought from a surety, not the state. Price is a small percentage of the bond amount and depends on your credit.

  • Surety bond · $20,000

Liability insurance

Some states require proof of general liability or workers' compensation coverage at licensing time.

  • Insurance

Business registration

If you plan to contract in your own name, budget for a business license or entity registration on top of the trade license.

  • Business license

How Alaska licenses residential contractors

Alaska residential contractor · “General Contractor with Residential Contractor Endorsement

Statewide license

Verified September 17, 2026· 6 sources

Issued by Alaska Division of Corporations, Business and Professional Licensing (Construction Contractors Program)

Alaska licenses homebuilders statewide through the Construction Contractors Program in the Division of Corporations, Business and Professional Licensing, part of the Department of Commerce, Community, and Economic Development. The credential comes in two pieces. The registration is held by the business: an individual, partnership, corporation or LLC registers as a General Contractor with Residential Endorsement, posts a $20,000 surety bond, files public liability and property damage insurance, and pays a $100 application fee and a $250 registration fee. The residential contractor endorsement itself is held by a person and assigned to that registered general contractor, and it is what unlocks residential work: no general contractor may build or bid a privately owned residential structure of one to four units, or alter one by more than 25 percent of its value, unless the contractor holds the endorsement or has an endorsement holder assigned to it. To earn the endorsement an individual completes a 16-hour cold climate course and passes the Alaska residential contractor endorsement examination on arctic structural and thermal construction. The endorsement holder must be the sole proprietor, a partner, an employee, director or officer of the corporation, or an employee or member of the LLC, and may be assigned to no more than two general contractors at a time.

Moving to AlaskaLeaving Alaska

Why Texas has nothing to transfer

Texas residential contractor

Licensed by cities and counties

Verified September 17, 2026· 15 sources

Texas issues no statewide residential contractor, home builder or remodeler license, and no state agency examines or qualifies people who build houses. The Texas Residential Construction Commission, which registered builders and remodelers from 2003, was abolished and its Act expired on September 1, 2009, and nothing replaced it. What Texas does license are individual trades: electricians and air conditioning and refrigeration contractors through the Texas Department of Licensing and Regulation, and plumbers through the Texas State Board of Plumbing Examiners, so a builder who self-performs that work needs the matching state license. Residential contracting itself is regulated, where at all, by cities through registration, insurance, bonding and permitting: San Antonio, Fort Worth, El Paso, Dallas and Austin all require a residential builder or home-improvement contractor to register before pulling a permit, while Houston states that general contractors are not required to be licensed. A builder moving to Texas therefore has no state license to transfer and no reciprocity to apply for; the practical work is registering in each city where they build, carrying the insurance and bonds those cities require, and hiring or becoming state-licensed trades. The one credential that does travel is a national ICC certification, which San Antonio accepts from the registration holder or a designated Certified Agent.

How local licensing works in Texas

How it works in Texas. There is no state license, no state application and no state exam for residential contractors. Cities control who may pull a residential building permit, and each city sets its own rules, so a builder registers separately in every jurisdiction where they work. Registration is about identity, insurance, bonding and (in one city) a national certification - not about trade competence testing, and not about what license you held in your last state. Nothing an out-of-state residential contractor holds gives a discount on any of it.

San Antonio. Development Services runs the most demanding residential program in the state, under Chapter 10-115 of the Code of Ordinances, with two registrations. A Residential Building Contractor registration covers 'the constructing, structural alteration, or enlarging any one or two-family detached dwelling' (new homes, additions, foundations, roofing, pools and spas, fences, minor repairs). It requires an FBI criminal history record dated within 30 days of submittal, liability insurance of at least $500,000 per occurrence, $1,000,000 aggregate and $500,000 aggregate for products and completed operations with the City of San Antonio as certificate holder, and a certification: 'either the registration holder or one agent affiliated with the contractor must obtain a Residential ICC Certification or other certifications approved by the Building Official; or the company has a minimum of 5 years of continued registration with no violations ... suspensions, or revocation.' The fee is $170 and the term is two years. A Home Improvement Contractor registration covers 'nonstructural repair, replacement, remodeling, alteration, conversion, or modernization to any existing building', needs the same FBI background check and insurance of at least $300,000 per occurrence and $600,000 aggregate, costs $150 for two years, and carries no certification requirement. Both applications ask whether the applicant has lost or been suspended from home improvement or residential building privileges in any Texas jurisdiction. Apply through the BuildSA portal or in person at 1901 S. Alamo Street; customer service is (210) 207-1111.

Dallas. Building Inspection registers general contractors on one form, and its own note defines the category broadly: 'A General Contractor includes, but is not limited to, the following: residential general contractor, commercial general contractor, roofing contractor, fence contractor, foundation contractor, demolition contractor and pool contractor.' The form states an annual registration or renewal fee of $120.00 and requires a contracting company addressed inside the city limits to give a Certificate of Occupancy number or have a home office form on file. The responsible party assigns PINs to the company staff allowed to sign permit applications. There is no exam and no experience requirement. Registrations are renewed in person at a Building Inspection office or online through DallasNow; call (214) 948-4480.

Fort Worth. Development Services requires that 'any firm, business, individual or organization obtaining a permit related to the building, mechanical, plumbing or electrical provisions' of the city codes hold a valid Contractor Registration, with a carve-out for a single-family homeowner working on their own residence. A residential builder registers as a Building Contractor: the completed application plus a copy of a valid driver's license, $168.75, expiring one year from the date of issuance. No trade license, exam or experience documentation is required for that type. Customer service is 817-392-2222.

El Paso. Planning and Inspections registers a General Contractor for 'New Residential, Additions, Alterations, and Roofing' as well as commercial work. The packet is an Assumed Name Certificate or corporate documents, the Contractor Registration Application, a certificate of general liability insurance of at least $100,000 with the City of El Paso as certificate holder, and a blanket building construction bond - the current application states $50,000 for general contractors, while the city's requirements sheet lists $25,000 (confirm the amount with the One Stop Shop before buying the bond). A $10,000 blanket bond covers a defined list of minor work such as fences, tents, temporary signs and patch-and-paint. The requirements sheet lists a $102.00 annual fee. The application 'must be filed annually to be eligible to obtain permits from the City of El Paso in accordance with Section 18.02.104.5 of the El Paso City Code.' One Stop Shop, 811 Texas Avenue, 915-212-0104.

Austin. Development Services is explicit that 'in Texas, anyone can be a General Contractor, including homeowners, and a state license is not required', but the general contractor named on a building permit must first register with Building and Trade Contractor Services through an Austin Build + Connect (AB+C) portal account, submitting the web registration form and a Letter of Authorization. General contractors register once and update only when their name, address or authorized agents change; the city publishes no fee for the registration.

Houston. Houston requires nothing of a residential builder. Its Residential Permitting 101 guide states that 'the building permit may be purchased by the owner, agent, contractor. General Contractors are not required to be licensed', and the plan review page repeats that 'a general contractor's license is not required to obtain building permits.' What Houston does require is that the trades register their state licenses with the city: a TDLR-licensed Master Electrician, a TDLR Class A or B air conditioning contractor and a TSBPE-licensed Master Plumber must each be registered with the City of Houston before buying a trade permit, and a sidewalk or driveway permit needs a contractor with a $2,000 surety bond.

Everywhere else. Smaller Texas cities and unincorporated county areas vary widely; many require only a permit and proof of insurance, and counties generally have no building-permit authority at all outside a city's limits and extraterritorial jurisdiction. Check the building or development services department of each city before contracting there.

Moving to TexasLeaving Texas

Common questions

Do I have to take the Alaska residential contractor exam if I'm licensed in Texas?
Yes. Alaska requires the trade exam on this path.
What does it cost to get a Alaska residential contractor license from Texas?
Published fees on this path total $500, not counting exam vendor fees or bonds.
Do my Texas work hours count in Alaska?
No. Alaska does not credit out-of-state hours on this path.
Does it work the other way, from Alaska to Texas?
Not necessarily. Reciprocity is directed. Going from Alaska to Texas, the mechanism is not applicable.

Sources

  1. Construction Contractor Professional Licensing - Bond and Insurance Quick Facts · Alaska Department of Commerce, Community, and Economic Development (CBPL) · Other · verified September 17, 2026
  2. Construction Contractors - Alaska Division of Corporations, Business and Professional Licensing · Alaska Department of Commerce, Community, and Economic Development (CBPL) · Agency Page · verified September 17, 2026
  3. Construction Contractors FAQs - Alaska Division of Corporations, Business and Professional Licensing · Alaska Department of Commerce, Community, and Economic Development (CBPL) · Faq · verified September 17, 2026
  4. Applications and Forms - Alaska Construction Contractors Program · Alaska Department of Commerce, Community, and Economic Development (CBPL) · Agency Page · verified September 17, 2026
  5. Statutes and Regulations - Construction Contractors (AS 08.18 and 12 AAC 21), September 2023 · AS 08.18.011, .013, .021, .024, .025, .031, .041, .051, .071, .101; 12 AAC 21.650, .660, .680, .690, .695, .700 · Alaska Department of Commerce, Community, and Economic Development (CBPL) · Admin Rule · verified September 17, 2026
  6. Form 08-4819 - General Contractor with Residential Endorsement Registration Application (rev. 09/03/2025) · Alaska Department of Commerce, Community, and Economic Development (CBPL) · Form · verified September 17, 2026
  7. License Expiration Dates - Alaska Division of Corporations, Business and Professional Licensing · Alaska Department of Commerce, Community, and Economic Development (CBPL) · Agency Page · verified September 17, 2026
  8. National Organizations - Alaska Construction Contractors Program · Alaska Department of Commerce, Community, and Economic Development (CBPL) · Agency Page · verified September 17, 2026
  9. Alaska Residential Contractor Endorsement Examination - PSI Candidate Information Bulletin · PSI Services LLC for the Alaska Division of Corporations, Business and Professional Licensing · Other · verified September 17, 2026
  10. Form 08-4161 - Contractor Residential Endorsement Application (rev. 04/19/2024) · Alaska Department of Commerce, Community, and Economic Development (CBPL) · Form · verified September 17, 2026
  11. Residential Endorsement Exam Information - Alaska Construction Contractors Program · Alaska Department of Commerce, Community, and Economic Development (CBPL) · Agency Page · verified September 17, 2026
  12. NASCLA Accredited Examination for Commercial General Building Contractors · National Association of State Contractors Licensing Agencies · Other · verified September 17, 2026

Verified dates are when a person last opened each source and confirmed the facts above. Cite the board, not us.

Report an error on this page

Related