Pennsylvania to Connecticut: master electrician license reciprocity
Pennsylvania does not issue a statewide master electrician license, so there is nothing to transfer. Here is Connecticut's standard path for out-of-state applicants.
Your origin state does not issue a statewide license at this level, so there is no license to transfer. The destination's standard out-of-state path is shown; expect to meet it in full.
Reference only, not legal advice. Rules change; confirm with the licensing board before you apply. Full disclaimer.
Contractor (E-1) by equivalent out-of-state license (all states)
Your out-of-state credentials give no advantage. You meet the destination's requirements from scratch.
A master electrician or electrical contractor licensed in any other state applies under DCP's 'Electrical Contractor - Equivalent Out of State License' path. DCP reviews a single out-of-state license for equivalency to the E-1: it must have required 720 classroom hours with a curriculum matching Exhibit A, 8,000 apprentice OJT hours and two years (4,000 hours) of licensed OJT, 12,000 hours in total. The applicant submits a copy of the license, an official license verification, the laws and regulations that set the requirements met to obtain it, and the scope of work for that license, with the non-refundable $150 application fee. If approved, the applicant must pass both the E-1 trade exam and the Business and Law exam through PSI ($59 per portion) and then pay the $150 initial license fee; the out-of-state license does not waive either exam because Connecticut has no reciprocal agreements. An applicant whose license is not found equivalent must document the classroom and OJT hours directly under the equivalent experience and training path.
The out-of-state license page does not restate the exam requirement; it follows from the Electrical License page, CGS 20-333 and the PSI bulletin, which states that all contractors must pass a Business and Law examination and a trade examination. CGS 20-333a allows licensure without examination only where the other state reciprocates for Connecticut licensees, and DCP states no such agreements exist. Whether DCP treats an out-of-state 'master' license (rather than a contractor license) as the E-1 equivalent depends on the hour and curriculum comparison; DCP publishes no list of accepted titles.
At a glance
- Trade exam
- Required
- Law / code exam
- Required
- Out-of-state hours
- Count toward eligibility
What you must already have
- Your Pennsylvania license must be active and in good standing.
- The out-of-state license must be equivalent: it required 720 classroom hours matching Exhibit A, 8,000 apprentice OJT hours and 4,000 licensed OJT hours (12,000 total)Only one out-of-state license is reviewed for equivalency.
- You must document at least 12,000 hours of qualifying work experience.8,000 hours as an apprentice plus 2 years (4,000 hours) working as a licensed journeyperson.
What you'll do to get licensed in Connecticut
- 1Application fee. Pay the application fee ($150). Contractor application fee, non-refundable (CGS 20-333).
- 2Other. Copy of the out-of-state license, official license verification, the laws/regulations listing the requirements met to obtain it, and the scope of work for that license.
- 3Trade exam. Pass the destination's trade exam. E-1 Unlimited Electrical Contractor trade exam administered by PSI: 100 questions, 4 hours, 70% to pass, open book (2020 or 2023 NEC).
- 4Law / code exam. Pass a law, rules, or code exam. Connecticut Business and Law exam (PSI): 50 questions, 2 hours, 70% to pass, based on the NASCLA Contractors Guide to Business, Law and Project Management, Connecticut 6th edition.
- 5Exam fee. Pay the exam fee ($59). PSI fee for the trade portion (same fee for retakes).
- 6Exam fee. Pay the exam fee ($59). PSI fee for the Business and Law portion (same fee for retakes).
- 7License fee. Pay the license or certificate fee ($150). Initial license fee for a contractor's license after passing both exams (CGS 20-335); renews annually for $150.
Published fees on this path total $418, excluding exam-vendor fees, bonds, and insurance.
What you'll need to buy or arrange
Exam preparation
Most boards contract PSI, Prov, or ICC for exams. Check which code edition the exam is written to before buying a prep course.
- Trade exam
- Law / code exam
- Exam fee · $59
- Exam fee · $59
How Connecticut licenses master electricians
Connecticut master electrician · “E-1 Unlimited Electrical Contractor”
Statewide license
Connecticut has no license titled 'master electrician'; the top-tier personal license is the E-1 Unlimited Electrical Contractor, issued by DCP to an individual (DCP licenses individuals, not companies) and permitting all electrical work under CGS 20-330, pulling permits and contracting with the public. A new E-1 applicant needs 720 classroom hours matching DCP's Exhibit A curriculum and 12,000 OJT hours (8,000 as an apprentice plus 4,000 hours, two years, working as a licensed journeyperson), reachable through two years as a Connecticut journeyperson, equivalent experience and training, or an equivalent out-of-state license, and must pass both the PSI E-1 trade exam (100 questions, 4 hours, 70%) and the Business and Law exam (50 questions, 2 hours, 70%). DCP states that Connecticut does not have reciprocal agreements with any other jurisdiction. Fees are a $150 application fee, $59 per exam portion and a $150 initial license fee; licenses expire every September 30 and renew for $150.
Why Pennsylvania has nothing to transfer
Pennsylvania master electrician
Licensed by cities and counties
Pennsylvania issues no statewide master electrician or electrical contractor license; none of the Department of State's licensing boards covers the trade, so the master-level credential exists only at the city level under names that vary: Philadelphia's Electrical Contractor License (four years with a licensed contractor, the ICC-administered Philadelphia Electrical Contractor exam, eight hours of NFPA 70 coursework, insurance, $60 application, $262 license and $202 annual renewal), Pittsburgh's Electrical Trade License (six years of combined experience and education, an ICC National Standard Master Electrician exam or the city exam, $1M/$2M liability insurance, $90 per year with eight hours of CE), and Master Electrician licenses in Allentown (four years, ICC G16, $50 application), Harrisburg (six years, ICC master exam, $125), Reading (two years as a journeyman, ICC G16Y, $90) and Scranton (four years plus ICC master exam, $250), with Erie licensing electrical contractors through its Trades Licensing Board. Because nearly every city relies on the ICC National Standard Master Electrician exam, a passing ICC score earned in another state is the most portable credential, and Pittsburgh's rules expressly allow the License Officer to accept equivalent out-of-state certification tests. Formal reciprocity is limited to Harrisburg (Maryland, Delaware and several Pennsylvania cities) and Reading (a published list that includes Delaware, Maryland, Michigan, New Jersey, South Carolina, Virginia and West Virginia); an out-of-state master must otherwise apply to each city separately, document local experience thresholds and pay each city's fees.
How local licensing works in Pennsylvania
How local licensing works. Pennsylvania has no state electrical board. Each city that licenses electricians does so under its own ordinance through a local board, and a license is valid only in the issuing city unless that city's rules recognize another jurisdiction. Nearly all cities use ICC exams, and several accept any ICC master exam regardless of code year.
Philadelphia. The Department of Licenses and Inspections issues the Electrical Contractor License (Philadelphia Code 9-1006), the city's only master-level electrician credential; it is issued to the individual, who must also hold a Commercial Activity License. Requirements: a minimum of four years of employment doing electrical work for a company licensed through a local or state jurisdiction (two years of electrical education equals one year of experience, up to two years), proven by tax records from a licensed contractor or proof of licensure through a local or state jurisdiction subject to L&I approval; a passing Philadelphia Electrical Contractor Examination administered by ICC referencing the current Philadelphia Code (or an application within 12 months of passing); eight hours of NFPA 70 coursework approved by the PA Department of Labor and Industry within the preceding 12 months; general liability $500,000 per occurrence, auto $300,000 and workers' compensation $100,000/$100,000/$500,000 naming the city as certificate holder. Fees: $60 non-refundable application, $262 license, $202 annual renewal with a 1.5 percent monthly surcharge after 60 days. Out-of-state licensure can serve as proof of experience but does not waive the Philadelphia exam.
Pittsburgh. The Department of Permits, Licenses and Inspections issues the Electrical Trade License to individuals performing work that requires an electrical permit (PLI Rules VI.6; PCC 747). Applicants show a passing City-proctored Master Electrical exam or an ICC Standard Master Electrician exam for any code year (T16, G16, F16 or older) and six years of combined experience and education evaluated by the License Officer, with employer or licensed-electrician statements; insurance is $1,000,000 per occurrence / $2,000,000 aggregate general liability plus workers' compensation or a no-employee affidavit. The license costs $90 (2025 fee schedule), expires 365 days from issue and renews with eight hours of continuing education. PLI Rule VI.1(E)(d) states that equivalent certification testing programs from other states are accepted upon the License Officer's determination of equivalence.
Allentown. The Electricians' Examining Board issues a Master license on four years of practical experience and the ICC National Standard Master exam (G16); applicants must be over 21 with a high school diploma or GED, pay a $50 non-refundable application fee, obtain Board approval before scheduling the exam, and pay an annual license fee set in the Business Regulation and Tax Code. No reciprocity provision is published.
Harrisburg. The Bureau of Codes issues a Master Electrician license ($125) on six years of practical experience or four years of technical school plus four years, with a passing ICC Master, National Standard Master or Pennsylvania (Philadelphia) Standard Master exam, insurance of $1,000,000 property damage and $300,000 bodily injury per occurrence, and a Mercantile Tax License. Documentation may be by test results or by reciprocity from Allentown, Bethlehem, Lancaster, Reading, Philadelphia, Maryland or Delaware (others considered case by case); a letter of good standing is required from any other Pennsylvania municipality that licenses the applicant.
Reading. The Electrical Board issues a Master Electrician license ($90 annual) to holders of a Reading or reciprocated journeyman license for two years who pass the ICC G16Y master exam. A reciprocal master license ($190 including a one-time reciprocity fee) recognizes licenses from jurisdictions of at least third-class-city standing with an equivalent board and standards; the June 2023 list names Bethlehem, Easton, Erie, Harrisburg, Philadelphia and Scranton, Springfield MO, Sullivan County NY, and the states of Delaware, Maryland (master), Michigan, New Jersey, South Carolina, Virginia and West Virginia. Reciprocal licenses become permanent Reading licenses.
Scranton. Licensing, Inspections and Permits issues a Master Electrical contractor license ($250, calendar year) on four years under a licensed contractor (W-2s or 1099s), a passing ICC/UCC Master Electrical exam, general liability of $500,000 per person / $1,000,000 per occurrence and a Single Tax Office registration; an alternative route uses eight years of experience plus notarized referral letters in place of the exam. The form asks for copies of licenses held in other municipalities but states no reciprocity rule.
Erie. All electrical work must be done by an electrical contractor licensed by the City of Erie and only master license holders may obtain permits; the Trades Licensing Board reviews applications under Article 333 of the Codified Ordinances (not openable), which per the Board page also provides 90-day temporary apprentice and journeyman licenses.
Out-of-state holders. Apart from Harrisburg's and Reading's lists there is no reciprocity. The practical path is to present an ICC National Standard Master Electrician exam result (accepted by Pittsburgh for any code year and by Harrisburg, Allentown, Reading and Scranton), document the local experience threshold, meet each city's insurance requirement and pay its fee; Philadelphia requires its own ICC-administered Philadelphia exam.
Common questions
- Do I have to take the Connecticut master electrician exam if I'm licensed in Pennsylvania?
- Yes. Connecticut requires the trade exam on this path, plus a law or code exam.
- What does it cost to get a Connecticut master electrician license from Pennsylvania?
- Published fees on this path total $418, not counting exam vendor fees or bonds.
- Do my Pennsylvania work hours count in Connecticut?
- Yes. Documented out-of-state experience counts toward Connecticut's eligibility requirements.
- Does it work the other way, from Connecticut to Pennsylvania?
- Not necessarily. Reciprocity is directed. Going from Connecticut to Pennsylvania, the mechanism is not applicable.
Sources
- Connecticut General Statutes Chapter 393 - Occupational Licensing (Electrical, Plumbing and Piping, Heating, Cooling...) · CGS §§ 20-333, 20-333a, 20-334a, 20-335 · Connecticut General Assembly · Statute · verified September 15, 2026§20-333: non-refundable application fee of $90 for limited licenses and journeyman-type licenses under 20-334a(a)(2)-(3) and $150 for unlimited contractor licenses under 20-334a(a)(1); competency is shown by examination. §20-333a Reciprocity: the Commissioner may grant a license without examination to a currently practicing, competent person holding a similar license from another state with substantially similar or higher requirements, but only if that state grants the same privilege to Connecticut licensees; DCP reports no such agreements exist. §20-334a(a)(1)(A): an unlimited contractor's license may be issued to a person who served as a journeyman in the trade for at least two years 'and, if such service as a journeyman was outside this state, has furnished evidence satisfactory to the appropriate state board or the department that such service is comparable to similar service in this state', and has passed the examination; (a)(2)(A): an unlimited journeyman's license requires a bona fide apprenticeship including not less than four years' experience and passing the state licensure examination. §20-335: initial license fee $150 for a contractor's license and $120 for any other license; licenses expire annually; renewal $150 contractor / $120 other. The page returned a TLS certificate error to the fetch tool on 2026-09-15 and was downloaded directly with curl to read the section text.
- Connecticut DCP - Electrical Contractor: Equivalent Experience and Training · Connecticut Department of Consumer Protection · Agency Page · verified September 15, 2026Fallback path when an out-of-state license is not found equivalent: E-1 needs 720 classroom hours equivalent to the Exhibit A courses, 8,000 apprentice OJT hours and 4,000 licensed OJT hours (12,000 total), documented by transcripts/diplomas, notarized employer letters with dates and work descriptions, and out-of-state completion certificates. Continuing-education and manufacturer certificates are not accepted, and OJT cannot substitute for classroom hours.
- Connecticut DCP - Electrical Contractor: Equivalent Out of State License · Connecticut Department of Consumer Protection · Agency Page · verified September 15, 2026Same equivalency definition as the journeyperson page. E-1 requires 8,000 apprentice OJT hours plus 2 years (4,000 hours) of licensed OJT for 12,000 total OJT hours, and 720 classroom hours matching Exhibit A (required courses). Same document list; only one out-of-state license is reviewed. Does not state exam requirements or fee amounts itself.
- Connecticut DCP - Electrical License (application paths, fees, renewal) · Connecticut Department of Consumer Protection · Agency Page · verified September 15, 2026Lists the six application paths (contractor: 2+ years as journeyperson, equivalent experience and training, equivalent out-of-state license; journeyperson: Connecticut apprenticeship, equivalent experience and training, equivalent out-of-state license). Application fee: contractor $150, journeyperson $90, non-refundable. Renewal: contractor $150, journeyperson $120; all licenses expire September 30 annually. States 'Separate fees will be due to the exam vendor at time of exam registration' and, verbatim, 'Connecticut does not have reciprocal agreements with any other jurisdiction.'
- Connecticut DCP - Electrical License Types and Scope of Work · Connecticut Department of Consumer Protection · Agency Page · verified September 15, 2026E-1 Unlimited Electrical Contractor: all electrical work as defined in CGS 20-330. E-2 Unlimited Electrical Journeyperson: all electrical work, only while employed by a properly licensed contractor. Also lists the limited classes (C-5/C-6, C-7/C-8, L-1/L-2, L-5/L-6, T-1/T-2, PV-1/PV-2).
- Connecticut DCP Occupational Licensing - Electrical Trades Candidate Information Bulletin (PSI, updated 2/4/2026) · Connecticut Department of Consumer Protection / PSI Services LLC · Other · verified September 15, 2026Eligibility for examination is determined by the State (DCP approves the application, then PSI schedules). Fee: $59 per examination portion, first attempt or retake, non-refundable. Journeypersons pass only a trade portion; contractors must pass both a trade portion and the Business and Law portion (50 questions, 2 hours, 70%, based on the NASCLA Contractors Guide, Connecticut 6th edition). E-1 Unlimited Electrical Contractor trade exam: 100 questions, 4 hours, 70%, open book. E-2 Unlimited Electrical Journeyperson: 80 questions, 3.5 hours, 70%, open book. Code questions are based on the 2020 or 2023 National Electrical Code. Eligibilities are valid for one year; a passed portion is valid for two years.
Verified dates are when a person last opened each source and confirmed the facts above. Cite the board, not us.