Missouri to Connecticut: master HVAC technician license reciprocity
Missouri does not issue a statewide master HVAC technician license, so there is nothing to transfer. Here is Connecticut's standard path for out-of-state applicants.
Your origin state does not issue a statewide license at this level, so there is no license to transfer. The destination's standard out-of-state path is shown; expect to meet it in full.
Reference only, not legal advice. Rules change; confirm with the licensing board before you apply. Full disclaimer.
Contractor (S-1) by equivalent out-of-state license (all states)
Your out-of-state credentials give no advantage. You meet the destination's requirements from scratch.
A master HVAC technician or HVAC/mechanical contractor licensed in any other state applies under DCP's 'Heating Contractor - Equivalent Out of State License' path. DCP reviews a single out-of-state license for equivalency to the S-1: it must have required 576 classroom hours with a curriculum matching Exhibit A and 12,000 on-the-job hours (8,000 as an apprentice plus two years as a licensed journeyperson); the limited D-1 class needs 8,000 OJT and 432 classroom hours and the B-1 needs 6,000 and 288. The applicant submits a copy of the license, an official license verification, the laws and regulations that set the requirements met to obtain it, and the scope of work for that license, with the non-refundable $150 application fee. If approved, the applicant must pass both the S-1 trade exam and the Business and Law exam through PSI ($59 per portion) and then pay the $150 initial license fee; the out-of-state license does not waive either exam because Connecticut has no reciprocal agreements. An applicant whose license is not found equivalent must document the classroom and OJT hours directly under the equivalent experience and training path, where out-of-state journeyman service counts if DCP finds it comparable (CGS 20-334a(a)(1)(A)).
The out-of-state license page does not restate the exam requirement; it follows from the Heating, Cooling and Sheet Metal Work Licenses page, CGS 20-334a(a)(1)(A) and the PSI bulletin, which states that all contractors must pass a Business and Law examination and a trade examination. CGS 20-333a allows licensure without examination only where the other state reciprocates for Connecticut licensees, and DCP states no such agreements exist. Whether DCP treats an out-of-state 'master HVAC' license (rather than a contractor license) as the S-1 equivalent depends on the hour and curriculum comparison; DCP publishes no list of accepted titles. EPA Section 608 is not mentioned on the DCP pages but applies federally to anyone handling refrigerants.
At a glance
- Trade exam
- Required
- Law / code exam
- Required
- Out-of-state hours
- Count toward eligibility
What you must already have
- Your Missouri license must be active and in good standing.
- The out-of-state license must be equivalent: it required 576 classroom hours matching Exhibit A and 12,000 OJT hours for the S-1 (D-1: 432 classroom / 8,000 OJT; B-1: 288 / 6,000)Only one out-of-state license is reviewed for equivalency.
- You must document at least 12,000 hours of qualifying work experience.8,000 hours as an apprentice plus 2 years (4,000 hours) working as a licensed journeyperson; journeyman service outside Connecticut counts if DCP finds it comparable.
What you'll do to get licensed in Connecticut
- 1Application fee. Pay the application fee ($150). Contractor application fee, non-refundable (CGS 20-333).
- 2Other. Copy of the out-of-state license, official license verification, the laws/regulations listing the requirements met to obtain it, and the scope of work for that license.
- 3Trade exam. Pass the destination's trade exam. S-1 Unlimited Heating, Piping and Cooling Contractor trade exam administered by PSI: 80 questions, 3 hours, 70% to pass, open book (D-1: 70 questions, 3 hours; B-1: 50 questions, 2 hours).
- 4Law / code exam. Pass a law, rules, or code exam. Connecticut Business and Law exam (PSI): 50 questions, 2 hours, 70% to pass, based on the NASCLA Contractors Guide to Business, Law and Project Management, Connecticut 6th edition.
- 5Exam fee. Pay the exam fee ($59). PSI fee for the trade portion (same fee for retakes).
- 6Exam fee. Pay the exam fee ($59). PSI fee for the Business and Law portion (same fee for retakes).
- 7License fee. Pay the license or certificate fee ($150). Initial license fee for a contractor's license after passing both exams (CGS 20-335); renews annually for $150, expiring August 31.
- 8Other. Hold EPA Section 608 technician certification to handle refrigerant; federal law requires it, but it is not a condition of this state license (if applicable).
Published fees on this path total $418, excluding exam-vendor fees, bonds, and insurance.
What you'll need to buy or arrange
Exam preparation
Most boards contract PSI, Prov, or ICC for exams. Check which code edition the exam is written to before buying a prep course.
- Trade exam
- Law / code exam
- Exam fee · $59
- Exam fee · $59
- Other · if applicable
How Connecticut licenses master HVAC technicians
Connecticut master HVAC technician · “S-1 Unlimited Heating, Piping and Cooling Contractor”
Statewide license
Connecticut has no license titled 'master HVAC'; the top-tier personal credential is the S-1 Unlimited Heating, Piping and Cooling Contractor, issued by DCP to an individual (DCP licenses individuals, not companies) and permitting all heating, piping and cooling work under CGS 20-330, pulling permits and contracting with the public. Limited contractor classes cover narrower scopes, chiefly the D-1 Limited Warm Air, Air Conditioning and Refrigeration Contractor and the B-1 Limited Gas and Oil Burner Contractor. A new S-1 applicant needs 576 classroom hours matching DCP's Exhibit A curriculum and 12,000 OJT hours (8,000 as an apprentice plus two years, 4,000 hours, working as a licensed journeyperson), reachable through two years as a Connecticut journeyperson, equivalent experience and training, or an equivalent out-of-state license, and must pass both the PSI S-1 trade exam (80 questions, 3 hours, 70%) and the Business and Law exam (50 questions, 2 hours, 70%). CGS 20-334a(a)(1) expressly allows journeyman service performed outside Connecticut to count if DCP finds it comparable. DCP states that Connecticut does not have reciprocal agreements with any other jurisdiction. Fees are a $150 application fee, $59 per exam portion and a $150 initial license fee; licenses expire every August 31 and renew for $150.
Why Missouri has nothing to transfer
Missouri master HVAC technician
Licensed by cities and counties
Missouri does not issue a master HVAC license or a statewide mechanical contractor license; the Division of Professional Registration licenses no HVAC or mechanical profession, and unlike the electrical trade there is no voluntary statewide contractor license for HVAC. The master-level credential exists only at the local level under names that vary by jurisdiction: Springfield certifies Master Mechanical craftsmen (4 years as a certified journeyman or 10 years of experience, ICC exam, $50), Kansas City issues a mechanical certificate of qualification to the supervisor who qualifies a licensed mechanical contractor (Prometric or ICC exam, $60 application, $181 four-year renewal), and St. Louis County and the City of St. Louis license mechanical contractors through their boards of examiners. An out-of-state master HVAC license carries no state-level recognition in Missouri, and none of these jurisdictions publish a reciprocity path for it; Springfield accepts an identical ICC, Prometric, Experior or Block exam score in place of retesting and Kansas City may accept a comparable exam it deems equivalent. A master arriving from another state should expect to qualify in each jurisdiction separately and then obtain that jurisdiction's mechanical contractor license to pull permits. EPA Section 608 certification is a separate federal requirement.
How local licensing works in Missouri
How local licensing works. Missouri has no state HVAC license and no statute standardizing local HVAC licensing; each city or county sets its own master, supervisor and contractor requirements.
Springfield. Building Development Services certifies Master Mechanical craftsmen: 4 years as a certified journeyman in the trade or 10 years of satisfactory experience, documented on notarized employer forms and approved by the Building and Trades board; ICC master mechanical exam through Pearson Vue (about $125), 75% to pass; certification card $50 with $50 annual renewal. 'Reciprocation' applicants submit copies of their other-state licenses and an identical-exam score of 75% or better from Prometric, Experior, Block or ICC; otherwise they test.
Kansas City. City Planning and Development licenses mechanical contractors ($55 application, $181 issuance, $181 renewal every four years) whose scope covers heating, duct and ventilation systems, refrigeration maintenance, gas piping to burners and control wiring. Every licensed contractor must employ a full-time supervisor who holds a Kansas City certificate of qualification in the mechanical trade; the certificate requires an application with notarized references and a passing score from a recognized agency such as Prometric or ICC ($60 application, first four-year certificate free, $181 renewal), and the city may accept a comparable exam from another jurisdiction if it deems it equivalent or superior.
St. Louis County. The Board of Examiners for Mechanical Licensing certifies mechanical contractors (a certified contractor list is published) and requires a licensed mechanical contractor bond and, for some applicants, a financial responsibility bond; applications and renewals go through the Accela portal. Master-level exam and experience details are not published on the pages that could be opened.
City of St. Louis. The Mechanical Contractors Board of Examiners (Ordinance 62579, City Code 25.10) reviews each applicant's qualifications for a Mechanical Contractor's license issued by the Building Division; the license is required to pull mechanical permits for boilers, furnaces, exhaust systems and ventilation. Contractors also need the city's graduated business license.
Out-of-state holders. No reciprocity or endorsement path for another state's master HVAC license was found in any of these jurisdictions. The practical route is to present an identical ICC or Prometric master mechanical score where accepted (Springfield; Kansas City case by case), document experience, and apply for the local master certificate and contractor license in each jurisdiction where work will be performed.
Common questions
- Do I have to take the Connecticut master HVAC technician exam if I'm licensed in Missouri?
- Yes. Connecticut requires the trade exam on this path, plus a law or code exam.
- What does it cost to get a Connecticut master HVAC technician license from Missouri?
- Published fees on this path total $418, not counting exam vendor fees or bonds.
- Do my Missouri work hours count in Connecticut?
- Yes. Documented out-of-state experience counts toward Connecticut's eligibility requirements.
- Does it work the other way, from Connecticut to Missouri?
- Not necessarily. Reciprocity is directed. Going from Connecticut to Missouri, the mechanism is not applicable.
Sources
- Connecticut General Statutes Chapter 393 - Occupational Licensing (Electrical, Plumbing and Piping, Heating, Cooling...) · CGS §§ 20-333, 20-333a, 20-334a, 20-335 · Connecticut General Assembly · Statute · verified September 23, 2026
- Connecticut DCP - Heating Contractor: Equivalent Experience and Training · Connecticut Department of Consumer Protection · Agency Page · verified September 23, 2026
- Connecticut DCP - Heating Contractor: Equivalent Out of State License · Connecticut Department of Consumer Protection · Agency Page · verified September 15, 2026
- Connecticut DCP - Heating, Cooling and Sheet Metal Work Licenses (application paths, fees, renewal) · Connecticut Department of Consumer Protection · Agency Page · verified September 23, 2026
- Connecticut DCP - Heating, Piping, Cooling and Sheet Metal Work Examining Board · Connecticut Department of Consumer Protection · Agency Page · verified September 15, 2026
- Connecticut DCP - Heating, Piping and Cooling License Types and Scope of Work · Connecticut Department of Consumer Protection · Agency Page · verified September 15, 2026
- Connecticut DCP Occupational Licensing - Heating, Piping and Cooling Trades Candidate Information Bulletin (PSI, updated 2/4/2026) · Connecticut Department of Consumer Protection / PSI Services LLC · Form · verified September 23, 2026
- EPA Section 608 Technician Certification Requirements · 40 CFR Part 82, Subpart F (Clean Air Act §608) · U.S. Environmental Protection Agency · Other · verified September 15, 2026
Verified dates are when a person last opened each source and confirmed the facts above. Cite the board, not us.