Do I have to take the New Mexico master HVAC technician exam if I'm licensed in New York?

Yes. New Mexico requires the trade exam on this path, plus a law or code exam.

What does it cost to get a New Mexico master HVAC technician license from New York?

Published fees on this path total $273.76, not counting exam vendor fees or bonds.

Do my New York work hours count in New Mexico?

Yes. Documented out-of-state experience counts toward New Mexico's eligibility requirements.

Does it work the other way, from New Mexico to New York?

Not necessarily. Reciprocity is directed. Going from New Mexico to New York, the mechanism is not applicable.

New York to New Mexico: master HVAC technician license reciprocity

No credit· Start overVerified September 15, 2026· 7 sources

New York does not issue a statewide master HVAC technician license, so there is nothing to transfer. Here is New Mexico's standard path for out-of-state applicants.

Your origin state does not issue a statewide license at this level, so there is no license to transfer. The destination's standard out-of-state path is shown; expect to meet it in full.

Reference only, not legal advice. Rules change; confirm with the licensing board before you apply. Full disclaimer.

Out-of-state master HVAC or mechanical contractor (all states)

Your out-of-state credentials give no advantage. You meet the destination's requirements from scratch.

An out-of-state master HVAC technician or mechanical contractor receives no exam waiver in New Mexico. The applicant files the qualifying party application with PSI ($36) and a notarized work-experience affidavit showing four years of experience in the MM-3 classification within the past ten years (out-of-state experience is accepted), then must pass the 100-question MM-3 trade exam ($68.88, 75% to pass) and the Contractor's Business and Law exam ($68.88) or complete a commission-approved business and law course in its place. Once the certificate of qualification is issued, the individual or business applies for the MM-3 contractor's license ($30 application; $50 per year or $100 for the two-year term, or $100 per year for MM-98) and must carry workers' compensation coverage. Anyone who personally services refrigerant-containing equipment also needs federal EPA Section 608 certification, which CID requires of JR journeymen.

CID's pages describe no substantial-equivalence or endorsement review for contractors from any state; the statutory reciprocity authority in NMSA 60-13-14(C) has not been exercised for mechanical classifications as far as any official page shows. A qualifying party may also obtain the parallel JR journeyman certificate without new work-verification forms.

At a glance

Trade exam: Required
Law / code exam: Required
Out-of-state hours: Count toward eligibility

What you must already have

Four years of practical or related trade experience in the MM-3 classification within the ten years immediately before application (NMSA 60-13-14(B)(8); 14.6.6.10 NMAC)

What you'll do to get licensed in New Mexico

1Application fee. Pay the application fee ($36). Qualifying party application and work-experience affidavit fee paid to PSI.
2Trade exam. Pass the destination's trade exam. MM-3 Heat, Vent and Air Conditioning exam administered by PSI: 100 questions, 245 minutes, open book, 75% to pass.
3Exam fee. Pay the exam fee ($68.88). PSI fee for the MM-3 trade exam, first attempt or retake.
4Law / code exam. Pass a law, rules, or code exam. Contractor's Business and Law exam (required of all new candidates) or a commission-approved business and law course.
5Exam fee. Pay the exam fee ($68.88). PSI fee for the Business and Law exam.
6Contractor license. Hold or obtain a contractor license ($30). MM-3 contractor's license application fee, non-refundable (14.5.5.8 NMAC); the RLD page lists the company license application at $36.
7License fee. Pay the license or certificate fee ($100). MM-3 contractor's license fee, $50 per year or $100 for the two-year term; MM-98 is $100 per year or $200 for two years (14.5.5.8 NMAC).
8Insurance. Carry the required insurance. Workers' compensation coverage is required for all licensed entities.
9Other. EPA Section 608 technician certification (Type I/II/III/Universal) to handle refrigerants; federal, does not expire; required of anyone who personally services refrigerant circuits.

Published fees on this path total $273.76, excluding exam-vendor fees, bonds, and insurance.

What you'll need to buy or arrange

Exam preparation

Most boards contract PSI, Prov, or ICC for exams. Check which code edition the exam is written to before buying a prep course.

Trade exam
Exam fee · $68.88
Law / code exam
Exam fee · $68.88
Other

Liability insurance

Some states require proof of general liability or workers' compensation coverage at licensing time.

Insurance

How New Mexico licenses master HVAC technicians

New Mexico master HVAC technician · “MM-3 HVAC Contractor (qualifying party certificate of qualification)”

Statewide license

Verified September 15, 2026· 5 sources

Issued by New Mexico Construction Industries Division (Regulation and Licensing Department), Mechanical Bureau; applications and exams through PSI

New Mexico has no 'master HVAC' license. Its highest heating and cooling credential is the MM-3 Heating, Ventilation and Air Conditioning contractor classification (install, alter, repair, service and maintain HVAC air-handling and refrigeration equipment, piping and ductwork, with controls at 24 volts or less); the broader MM-98 Mechanical classification covers MM-3 plus plumbing, gas fitting and process piping. CID issues the contractor's license to the contracting entity and a personal, non-transferable certificate of qualification to the qualifying party, the individual who passed the MM-3 trade exam and the Contractor's Business and Law exam, so this site maps the MM-3 qualifying party to the master level. A qualifying party needs four years of experience in the classification within the ten years before application. Even with an MM-3 license the hands-on work must still be done by or under a certified JR or JSM journeyman. CID publishes reciprocity only for EE-98J electrical journeymen; no reciprocity or exam waiver is published for mechanical qualifying parties or contractors, although NMSA 60-13-14(C) allows the division to enter into reciprocal agreements with states having equivalent requirements.

Moving to New Mexico Leaving New Mexico

Why New York has nothing to transfer

New York master HVAC technician

Licensed by cities and counties

Verified September 15, 2026· 22 sources

New York issues no statewide master HVAC, mechanical or HVAC contractor license; the Department of State licenses none of the construction trades, so the master-level credential exists only where a city or county has created one, and most have not. The only examined, person-holdable HVAC license in the state is Buffalo's Heating Contractor license from the Board of Heating Examiners (age 21, two years of heating installation experience, a quarterly written exam, a $10,000 bond, $1,000,000 liability insurance, $50 exam fee and $500 a year), which covers heating and process systems but not air-conditioning-only work. New York City has no HVAC or mechanical contractor license at all (the DOB licenses oil burner installers and the FDNY certifies refrigerating system operating engineers, but installation and service of HVAC systems needs no license), and the suburban counties regulate the trade through home improvement contractor licensing of the business: Westchester has required 'all HVAC professionals' to hold its home improvement license since July 1, 2025 ($750 application, no exam), Nassau's home improvement license ($650 for two years plus $50, five years of experience, no exam) covers central heating and air-conditioning work, and Suffolk's ($200 application and $200 a year, $500,000 insurance, no exam) covers HVAC ductwork. An out-of-state master HVAC license has no state-level recognition and none of these jurisdictions publishes reciprocity for it; a contractor from another state obtains the local business license (or, in Buffalo, sits the heating contractor exam) in each jurisdiction where they will work.

How local licensing works in New York

How local licensing works. With no state HVAC board, each jurisdiction that regulates the trade does so under its own code, usually as a business license with insurance and experience requirements rather than a trade exam. Buffalo is the exception with an examined heating contractor license.

New York City. The Department of Buildings issues no HVAC, mechanical or refrigeration contractor license; mechanical work is done under permits without a trade license, and the general contractor registration ($300 for three years) applies only to builders of one- to three-family homes. Oil-fired equipment must be installed by a DOB-licensed Oil Burner Equipment Installer (Class A or B; written exam $585, practical exam $530, $100 license for three years), and any refrigerating system that needs an FDNY permit must be supervised by a holder of the FDNY Q-01 Refrigerating System Operating Engineer Certificate of Qualification (EPA Universal certification, a 200-hour course or one year of qualifying experience or a boiler engineer, marine engineer or PE license; $60 plus $225 exam fees; three-year renewal $15). Neither recognizes out-of-state HVAC licenses.

Buffalo. City Code Chapter 238 makes it unlawful for any person to install, erect, alter, repair, service, reset or replace any heating or process system without a license from the Board of Heating Examiners; the separate City contractor license 'does not allow for plumbing, heating, cooling or electrical work'. Applicants must be at least 21 and have two years of practical experience installing heating equipment, a recognized school course plus one year, or be a graduate engineer; they submit photo ID, employer letters and a list of twenty completed installations to the Office of Fuel Devices, and if approved sit the Heating Contractor's Examination (offered roughly every three months, covering local ordinances and ASHRAE material). Classes: I (oil, gas or solid fuel), II (gas or solid fuel), III (wood-burning fireplaces and stoves). Fees: $50 non-refundable testing fee, $500 license, $500 annual renewal; a $10,000 bond to the City and certificates of $1,000,000 general liability and workers' compensation insurance are required. The license may be held by an individual, partnership or corporation. No reciprocity provision.

Rochester. Licenses stationary engineers and refrigeration operators (plant operation), electricians and plumbers; no HVAC contractor license.

Westchester County. The June 2025 amendment to the Consumer Protection Code requires 'all HVAC professionals' to be licensed through the Department of Consumer Protection as of July 1, 2025; the vehicle is the county Home Improvement Contractor license ($750 application fee effective January 1, 2026, $100 optional expedite, roughly 60 business days of document verification and background investigation, no exam). The county's examined trade licenses cover only plumbers and electricians.

Nassau County. Contractors installing or replacing 'central heating or air conditioning systems' in residential property need the county Home Improvement license: five years of recent verifiable experience, an establishment in New York State, liability, property damage and workers' compensation insurance, $650 for a two-year license plus a one-time $50 restitution fund contribution, $110 late renewal fee; no exam.

Suffolk County. Home improvement contracting expressly includes 'ductwork for heating, ventilation and air-conditioning systems'; the county Home Improvement license requires public liability and property damage insurance of at least $500,000 per occurrence and workers' compensation, a $200 application fee and $200 annual license fee ($50 temporary 90-day license); employees of licensed contractors are exempt; no exam.

Out-of-state holders. No New York jurisdiction publishes a reciprocity or endorsement path for out-of-state HVAC contractor or master licenses. Buffalo requires its own exam; the counties require their own business license regardless of any license held elsewhere; New York City requires no HVAC license at all.

Moving to New York Leaving New York

Common questions

Do I have to take the New Mexico master HVAC technician exam if I'm licensed in New York?: Yes. New Mexico requires the trade exam on this path, plus a law or code exam.
What does it cost to get a New Mexico master HVAC technician license from New York?: Published fees on this path total $273.76, not counting exam vendor fees or bonds.
Do my New York work hours count in New Mexico?: Yes. Documented out-of-state experience counts toward New Mexico's eligibility requirements.
Does it work the other way, from New Mexico to New York?: Not necessarily. Reciprocity is directed. Going from New Mexico to New York, the mechanism is not applicable.

Sources

EPA Section 608 Technician Certification Requirements · 40 CFR Part 82, Subpart F (Clean Air Act §608) · U.S. Environmental Protection Agency · Other · verified September 15, 2026Federal requirement in every state: technicians who maintain, service, repair or dispose of equipment that could release refrigerants into the atmosphere must be certified (Type I small appliances, Type II high-pressure, Type III low-pressure, Universal). Apprentices under direct supervision are exempt. Certification does not expire; the core exam must be proctored for Universal certification. State HVAC boards commonly require it before licensure, but it is not itself a state license.
Construction Industries Licensing Act, NMSA 1978 Chapter 60, Article 13 (as of July 1, 2021) · NMSA 1978 §§ 60-13-14, 60-13-38 · New Mexico Regulation and Licensing Department · Statute · verified September 15, 2026Text extracted from the PDF locally. 60-13-14(B)(8): a license applicant must have had four years, within the ten years before application, of practical or related trade experience in the type of construction applied for. 60-13-14(C): 'The division, with the consent of the commission, may enter into a reciprocal licensing agreement with any state having equivalent licensing requirements.' 60-13-38: no person may work as a journeyman without a certificate of competence; categories include journeyman sheet metal worker and journeyman pipe fitter; applicants take an examination on rules and technical knowledge; eligibility requires two years' experience in the trade or the equivalent, or an approved vocational course.
14.5.5 NMAC - Fees (Construction Industries Division) · 14.5.5.8 and 14.5.5.9 NMAC · New Mexico Commission of Public Records, State Records Center and Archives · Admin Rule · verified September 15, 2026Non-refundable contractor's license application fee $30.00; license fee $100.00 per year or $200.00 for two years for the GA-98, GB-2, GB-98, GF-98, EE-98 and MM-98 classifications and $50.00 per year or $100.00 for two years for all other classifications (including MM-3). Journeyman certificate renewal fee $25.00 per year (14.5.5.9).
14.6.6 NMAC - Classification and Scope of Licenses and Certificates (mechanical and plumbing) · 14.6.6.10 and 14.6.6.11 NMAC · New Mexico Commission of Public Records, State Records Center and Archives · Admin Rule · verified September 15, 2026MM-3 Heating, Ventilation and Air Conditioning: four years of experience; scope is to 'install, alter, repair, service and maintain HVAC air handling and refrigeration equipment and piping, including fans, coils, condensing units, self-contained packaged air conditioning or heating units, evaporative cooling units, and ductwork' plus controls at 24 volts or less. MM-98 Mechanical (four years) covers MM-1 through MM-4 and the MS-3, MS-6, MS-12 and MS-14 specialties. Journeyman classifications: JR Journeyman Refrigeration (two years; 'must demonstrate compliance with environmental protection agency (EPA) recovery requirements before certificate may be issued'; works under MM-3, MM-4, MM-98 or JSM) and JSM Journeyman Sheet Metal (two years; works under MM-3 or MM-98).
State of New Mexico Contractor (Qualifying Party) Examinations Candidate Information Bulletin (PSI) · PSI Services for the NM Construction Industries Division · Other · verified September 15, 2026Text extracted from the PDF locally. Business and Law exam 'REQUIRED OF ALL NEW CANDIDATES' $68.88, or an approved Business and Law course may be taken instead; trade exams for MM-1, MM-2, MM-3, MM-4 and the MS specialties are $68.88 each, first time or retake. MM-3 Heat, Vent and Air Conditioning exam: 100 questions, 245 minutes, 75% (75 points) to pass, open book on the 2021 Uniform Mechanical Code, 2015 New Mexico Mechanical Code and Modern Refrigeration and Air Conditioning; content covers motors/controls, piping, heating and cooling equipment, refrigerants and refrigeration, and ductwork/ventilation. No reciprocity or out-of-state exam waiver is described.
NM CID / PSI - How to Obtain a Journeyman Certificate and Application for Journeyman Certificate (updated Aug 2025) · PSI Services for the NM Construction Industries Division · Form · verified September 15, 2026Text extracted from the PDF locally. States that mechanical work must be performed by or under the supervision of a certified journeyman even when a contractor's license is held. Experience table: JR Journeyman refrigeration and JSM Journeyman sheet metal require two years (4,000 hours); experience must have been gained while employed by a contractor licensed in the trade or be 'legal work in the state in which the work was performed'. Application fee $75.00 per classification, paid to PSI; notarized application and work experience affidavits; certificate active three years. Question 3(c) limits the reciprocity program to 'Electrical Journeyman (EE98J ONLY)'; question 3(p): a Journeyman Refrigeration (JR) applicant 'must attach proof of your EPA certification for refrigerant recovery'. Reciprocity applicants must have held the license at least one year in the state where they tested.
NM Regulation and Licensing Department - Apply for a Construction Industries License · New Mexico Regulation and Licensing Department, Construction Industries Division · Agency Page · verified September 15, 2026Section 'Reciprocal Journeyman in New Mexico': 'The only journeyman classification reciprocated in New Mexico is EE-98J, residential and commercial electrical'; no mechanical or refrigeration journeyman classification is reciprocated. Section 'Becoming a Qualifying Party': QP applicants need the required years of experience within the 10 years before application, must pass the classification exam(s) and a Contractor's Business and Law exam, must be pre-approved to schedule exams, and pay a $36 QP application and work-experience affidavit fee; the company license application fee is $36 plus license fees. No reciprocity is mentioned for qualifying parties or contractors.

Verified dates are when a person last opened each source and confirmed the facts above. Cite the board, not us.

Report an error on this page