Colorado to North Carolina: general contractor license reciprocity
Colorado does not issue a statewide general contractor license, so there is nothing to transfer. Here is North Carolina's standard path for out-of-state applicants.
Your origin state does not issue a statewide license at this level, so there is no license to transfer. The destination's standard out-of-state path is shown; expect to meet it in full.
Reference only, not legal advice. Rules change; confirm with the licensing board before you apply. Full disclaimer.
NASCLA Accredited Examination in place of the North Carolina Building Contractor examination
Your out-of-state credentials give no advantage. You meet the destination's requirements from scratch.
North Carolina does not recognize an out-of-state general contractor license on its own, but it does accept the NASCLA Accredited Examination for Commercial General Building Contractors in place of its own Building Contractor trade examination. That route is open to anyone regardless of which state licensed them: sit the NASCLA examination before applying, then file the North Carolina application with the NASCLA pass letter and transcript purchase receipt attached and take the North Carolina Business and Law examination. Everything else still applies in full, including the financial responsibility figure for the limitation requested, the background check, character references and entity registration. An applicant who does not hold the NASCLA credential and comes from a state without a waiver agreement simply takes the North Carolina Building Contractor examination instead: 90 questions, 200 minutes, 70% to pass. North Carolina requires no trade experience for licensure, so out-of-state years do not shorten any step.
The Board confirms NASCLA acceptance on its own contractor FAQ and in 21 NCAC 12A .0303(c), which names the NASCLA examination alongside an origin state examination as the qualifying exam. The FAQ states acceptance for the Building classification; it does not say the NASCLA examination is accepted for the Residential classification. The NASCLA examination is bought and scheduled from NASCLA, not from the Board or PSI, and it is taken before the North Carolina application is filed. Without NASCLA and without a waiver agreement, substitute the North Carolina Building Contractor examination for the waived trade examination below; the Business and Law examination is then part of that classification examination rather than a separate sitting.
At a glance
- Trade exam
- Waived
- Law / code exam
- Required
- Out-of-state hours
- Do not count
What you must already have
- You must have passed a licensing exam in Colorado that the destination considers comparable.NASCLA Accredited Examination for Commercial General Building Contractors, passed before the North Carolina application is filed. The Board asks for the NASCLA pass letter and the transcript purchase receipt to be attached to the application.
- The qualifier is at least 18 years old and possesses good moral character as determined by the Board (G.S. 87-10). North Carolina sets no minimum trade experience or apprenticeship hours for a general contractor license.
What you'll do to get licensed in North Carolina
- 1Law / code exam. Pass a law, rules, or code exam. North Carolina Business and Law examination: 40 questions, 90 minutes, 70% to pass, covering erosion and sedimentation control, licensing, liens, contracts, project management, safety and business practices. Required of applicants who qualify on the NASCLA examination rather than the North Carolina Building Contractor examination..
- 2Trade exam. Pass the destination's trade exam (if applicable). Not required if the NASCLA Accredited Examination has been passed. Otherwise the North Carolina Building Contractor examination applies: 90 questions, 200 minutes, 70% to pass, open book, administered by PSI Services LLC after the Board issues an eligibility letter..
- 3Application fee. Pay the application fee ($75). Nonrefundable application fee set by the limitation requested: $75 for a limited license, $100 for an intermediate license and $125 for an unlimited license (G.S. 87-10(a1); 21 NCAC 12A .0304(a)). The amount shown is the limited-license fee..
- 4Exam fee. Pay the exam fee ($79). $79 per examination, paid to PSI Services LLC when the examination is scheduled. The NASCLA examination itself is bought from NASCLA and is not covered by this fee..
- 5Financial responsibility. Show financial responsibility of at least $17,000. Evidence of financial responsibility for the entity that will hold the license. Current assets must exceed current liabilities by at least $17,000 for a limited license (or total net worth of at least $80,000), $75,000 for an intermediate license, or $150,000 for an unlimited license. Intermediate and unlimited applicants must show the figure in an agreed-upon procedures report on the Board form or an audited financial statement prepared by a CPA or independent accountant. Statements must be no more than twelve months old and conform to GAAP (21 NCAC 12A .0204). The amount shown is the limited-license working capital figure..
- 6Surety bond. Post a surety bond ($175,000) (if applicable). Optional alternative to the working capital or net worth figure: a continuous surety bond of $175,000 for a limited license, $500,000 for an intermediate license or $1,000,000 for an unlimited license, from a surety authorized in North Carolina and rated Superior or Excellent by A.M. Best. Proof is filed with the application and with every annual renewal, and the bond must stay in force until the licensee can show the required working capital (21 NCAC 12A .0204(e))..
- 7Background check. Complete a background check. Criminal background check through the third-party vendor the Board names, paid directly to the vendor. Every qualifier submits to the check, along with the sole proprietor, the president of a corporation, all managers and members of an LLC, or all partners of a partnership (21 NCAC 12A .0303(b))..
- 8Business license. Obtain a business license. The license is issued to a legal entity, so the individual, corporation, LLC or partnership that will contract must be formed and, if organized outside North Carolina, authorized to transact business in the State before the license is issued (G.S. 87-10.1)..
- 9Insurance. Carry the required insurance (if applicable). The Board states there is no insurance or bonding requirement for a general contractor license itself. North Carolina workers compensation law still applies to the business independently of licensure, and owners, lenders and general contractors commonly require general liability coverage by contract..
- 10Continuing education. Complete continuing education. Renewal condition rather than an entry requirement: at least one qualifier on a building, residential or unclassified license must complete eight hours of Board-approved continuing education each year, made up of a two-hour mandatory course and six elective hours, with up to four elective hours carried forward (G.S. 87-10.2)..
- 11Other. Letters of character reference required by 21 NCAC 12A .0303(a)(9) and .0308, certified copies of court records for any criminal convictions of the applicant or its qualifiers, and disclosure of disciplinary history with this or any other licensing agency..
Published fees on this path total $154, excluding exam-vendor fees, bonds, and insurance.
What you'll need to buy or arrange
Exam preparation
Most boards contract PSI, Prov, or ICC for exams. Check which code edition the exam is written to before buying a prep course.
- Law / code exam
- Trade exam · if applicable
- Exam fee · $79
Surety bond
A license or contractor bond is bought from a surety, not the state. Price is a small percentage of the bond amount and depends on your credit.
- Surety bond · $175,000 · if applicable
Business registration
If you plan to contract in your own name, budget for a business license or entity registration on top of the trade license.
- Business license
Liability insurance
Some states require proof of general liability or workers' compensation coverage at licensing time.
- Insurance · if applicable
Continuing education
Renewals usually need approved CE hours, often on the latest NEC. Reciprocal licensees are rarely exempt.
- Continuing education
How North Carolina licenses general contractors
North Carolina general contractor · “General Contractor, Building classification (Limited, Intermediate or Unlimited)”
Statewide license
Issued by North Carolina Licensing Board for General Contractors
The unlimited tier in North Carolina is the Building classification of the General Contractor license, issued by the North Carolina Licensing Board for General Contractors and required for any single undertaking costing $40,000 or more. The Building classification covers all building construction and demolition, commercial, industrial, institutional and residential alike, plus parking decks, site work and paving, storm drainage, retaining walls, recreational facilities and a list of specialty categories including concrete, masonry, roofing, metal erection, interior construction, swimming pools and asbestos. The Board also issues Highway, Public Utilities and Specialty classifications for work outside building construction, and separate North Carolina boards license the electrical, plumbing, heating and fire sprinkler trades. As with every classification, the license is held by a business and qualified by a named individual who passes the examination, and it carries a monetary limitation: Limited up to $750,000 per project, Intermediate up to $1,500,000, and Unlimited with no project cap, each set by the working capital, net worth or surety bond the applicant can show. North Carolina accepts the NASCLA Accredited Examination for this classification, and it holds examination waiver agreements with a short list of named states, but the Board states it does not have full reciprocity with any state.
Why Colorado has nothing to transfer
Colorado general contractor · “General / Building contractor license (Class A or B in most jurisdictions)”
Licensed by cities and counties
Colorado has no statewide general or commercial building contractor license. DORA licenses electricians and plumbers through its Division of Professions and Occupations but states on its own consumer page that general contractors are not licensed at the state level and that you should check with the city; the Pikes Peak Regional Building Department says the same thing in its exam notice. Unlimited and commercial building work is therefore licensed by each city, county or regional building department, typically as a Class A (unlimited) and Class B (limited commercial or under a height or storey cap) pair: Denver issues General Contractor Class A and Building Contractor Class B, Colorado Springs issues Building Contractor A-1, A-2, B-1 and B-2, Fort Collins issues Classes A, B, C1 and C2, and Aurora issues a single Commercial Building Contractor license. The license is held by the business and qualified by an individual who holds the supervisor certificate and has passed the relevant exam, so the person moving states applies for the certificate and the company applies for the license. The common thread is the ICC National Standard General Building Contractor (A) and Building Contractor (B) examinations, which nearly every Colorado jurisdiction requires, and a license must be obtained separately in each jurisdiction where the contractor will pull permits.
How local licensing works in Colorado
How local licensing works. Each Colorado jurisdiction licenses building contractors under its own ordinance and building code, and there is no state board above them. Class letters and size thresholds differ from place to place, so a Class B in Fort Collins is not a Class B in Colorado Springs. What is consistent is the exam: most jurisdictions require an ICC National Standard contractor examination, open book and multiple choice through Pearson VUE, and the Pikes Peak notice explains why that matters - "with successful passage of an ICC contractor exam, contractors can be secure in the knowledge that their results may be honored by many jurisdictions in Colorado and throughout the United States. However, each jurisdiction has the right to determine if this exam is acceptable." The same exam appears as W11, F11 or G11 for the unlimited (A) tier and W12, F12 or G12 for the limited (B) tier, depending on which code edition the jurisdiction has adopted, and departments generally require results from the current or a recent code year. The notice also warns that "passing an ICC contractor exam is NOT a license to practice and does not guarantee licensing in any jurisdiction."
Denver. The individual first earns a supervisor certificate. Class A covers "to erect, add to, alter, demolish, or repair any building or structure" and needs seven years of notarized commercial experience including ground-up high-rise work over 75 feet plus ICC exam #F11. Class B covers any building classified as less than a high rise and needs four years of notarized commercial experience on ground-up builds of 55 to 75 feet plus ICC exam #F12; Class B-2 caps the highest floor level or occupiable roof at 30 feet, with four years of experience including ground-up projects up to 40 feet, also on ICC #F12. Certificates cost $60 and renew every three years. The company then buys the General Contractor Class A or Building Contractor Class B license at $250 for three years. Denver states it "does not accept or reciprocate contractor licenses and/or certificates from other counties or states."
Colorado Springs, El Paso County and nearby towns (Pikes Peak Regional Building Department). Building Contractor A-1 covers "the construction, alteration and repair of any type or size of structure permitted by the Regional Building Code"; A-2 is the same except Group A, E and I occupancies over 30,000 square feet and any building requiring Type I construction; B-1 covers all occupancies except Groups A, E, I and H and Type I construction; B-2 covers nonstructural remodeling plus Group B, F, M or S buildings up to one storey and 7,500 square feet and Group R buildings up to 16 units and two storeys. License fees are $200 for A-1 and A-2, $175 for B-1 and B-2, on top of a $50 non-refundable application fee, and each of these classes requires an exam. Applicants supply three reference forms documenting experience, copies of all licenses held inside or outside Colorado, liability insurance naming PPRBD, workers' compensation, a Colorado certificate of good standing and a name-based judicial record check. Files close three weeks before the monthly Licensing Committee meeting, the Board of Review approves the following week, and the license must be claimed within 60 days. PPRBD accepts ICC National Standardized or ICC Colorado Standard exams passed on or after January 1, 2016 and states that "no out-of-state exams will be accepted."
Aurora. A single Commercial Building Contractor license "Requires ICC General Building Contractor 'A' OR 'B' Certification"; the supervisor license fee is $131 and the license fee is $392, plus registration and three job references. Limited Building Commercial and Demolition contractors register with three years of documented experience instead.
Fort Collins. Class A and A(DR) cover any building or structure; Class B and B(DR) cover new builds up to and including five storeys; Class C1 and C2 cover new builds up to three storeys and multi-family housing projects; E(C) covers nonstructural commercial alterations. Classes A and B require ICC exam G11 over the 2018 IBC plus the concrete manual, and Classes C1, C2 and E(C) require ICC exam G12, with G11 also accepted in place of G12. Every general contractor class also needs three project verifications with permits and final inspection records signed by someone unconnected to the applicant, and general liability of $1,000,000 per person with $2,000,000 per accident, property damage and aggregate. A new license with supervisor certificate is $300 for a two-year term including a $75 non-refundable application fee; renewals are $225. The city adopted the 2024 ICC codes with amendments in December 2025 and requires exam results from a current code year.
Boulder. Class A covers "the construction, alteration, wrecking, or repair of any type or size of building or structure permitted in the City of Boulder" and requires the ICC A Contractors certificate; Class B covers commercial and residential buildings of construction types V, IV, III-B and II-B and requires the ICC B certificate. New Class A and Class B applicants must also document education, training or years of experience in non-residential construction. Boulder states that it "does not accept reciprocal licenses from other jurisdictions," and its license covers work inside city limits only.
Jefferson County. Class A (labeled 2018 G11) covers "the construction, alteration, tenant finish or repair of any type of structure permitted by the Building Code" and Class B (2018 G12) covers commercial buildings and single- or multi-dwelling buildings up to three storeys. The county accepts "proof that you have passed an appropriate ICC exam within the last 3 years or ... a copy of a valid license issued from an ICC participating jurisdiction." The fee is $50 and licenses renew annually.
Arapahoe County. Building Contractor Class A (commercial) and Class B (commercial/residential) each cost $360 and require the matching ICC certification "or equivalent" certification by a recognized state or national certification entity; Class D specialty is $84. Insurance must carry a $2,000,000 general aggregate and $1,000,000 each occurrence, with the county as an additional holder.
Lakewood. Class A-1 Unlimited Commercial is "only issued to contractors with experience in building high-rise construction"; A-2 Limited Commercial is limited to two-storey commercial or four-storey R occupancies; A-4 covers commercial and residential remodeling not exceeding 30 percent of the original structure. A-1 and A-2 applicants attach any ICC certifications they or their employees hold. Fees are $150 for the first probationary year and $400 for each subsequent three-year renewal.
Douglas County. Unincorporated Douglas County registers general contractors rather than licensing them and states that it "has no testing requirements." Registration needs the application, workers' compensation proof or an exemption statement and business liability insurance naming the Building Division; fees are currently waived.
Out-of-state holders. None of the jurisdictions reviewed will convert another state's general contractor license into a Colorado one. Denver and Boulder rule it out in writing, and PPRBD will not accept exam results earned out of state. What does carry across is the ICC National Standard contractor certification: pass the (A) or (B) exam on a code edition the jurisdiction currently accepts and it will usually satisfy the testing requirement in Denver, Colorado Springs, Aurora, Fort Collins, Boulder, Jefferson County and Arapahoe County, though each department still verifies experience, references or project history separately and charges its own fee. Jefferson County goes further and accepts a current license from another ICC participating jurisdiction in place of the exam. Check the required class, exam code year and fee with each building department before applying, and expect to hold a license in every jurisdiction where you pull permits.
- Denver (Community Planning and Development)
- Colorado Springs / El Paso County (Pikes Peak Regional Building Department)
- Aurora (Building Division)
- Fort Collins (Planning and Development Services)
- Lakewood (Public Works)
- Boulder
- Jefferson County (Division of Building Safety)
- Arapahoe County (Building Division)
- Douglas County (Building Division)
Common questions
- Do I have to take the North Carolina general contractor exam if I'm licensed in Colorado?
- The trade exam is waived, but North Carolina requires a law or code exam.
- What does it cost to get a North Carolina general contractor license from Colorado?
- Published fees on this path total $154, not counting exam vendor fees or bonds.
- Do my Colorado work hours count in North Carolina?
- No. North Carolina does not credit out-of-state hours on this path.
- Does it work the other way, from North Carolina to Colorado?
- Not necessarily. Reciprocity is directed. Going from North Carolina to Colorado, the mechanism is not applicable.
Sources
- NASCLA Accredited Examination for Commercial General Building Contractors · National Association of State Contractors Licensing Agencies · Other · verified September 17, 2026
- N.C.G.S. 87-10 - Application for license; examination; certificate; renewal · N.C.G.S. 87-10(a), (a1), (b), (c), (c1), (e) · North Carolina General Assembly · Statute · verified September 17, 2026
- N.C.G.S. 87-15.1 - Reciprocity of licensing · N.C.G.S. 87-15.1 · North Carolina General Assembly · Statute · verified September 17, 2026
- Classifications and limitations - NC Licensing Board for General Contractors · North Carolina Licensing Board for General Contractors · Agency Page · verified September 17, 2026
- FAQ for Contractors - NC Licensing Board for General Contractors · North Carolina Licensing Board for General Contractors · Faq · verified September 17, 2026
- Laws and Regulations Applicable to General Contracting in the State of North Carolina (2026 edition) · 21 NCAC 12A .0202, .0204, .0303, .0304, .0402, .0403, .0404 · North Carolina Licensing Board for General Contractors · Admin Rule · verified September 17, 2026
- License applicants - NC Licensing Board for General Contractors · North Carolina Licensing Board for General Contractors · Agency Page · verified September 17, 2026
- Licensure Application Questions - License Type Selector (online application preview) · North Carolina Licensing Board for General Contractors · Form · verified September 17, 2026
- State of North Carolina Licensing Board for General Contractors - Candidate Information Bulletin · PSI Services LLC for the North Carolina Licensing Board for General Contractors · Other · verified September 17, 2026
Verified dates are when a person last opened each source and confirmed the facts above. Cite the board, not us.