LicensebyState

New York to North Carolina: general contractor license reciprocity

No credit· Start overVerified September 17, 2026· 9 sources

New York does not issue a statewide general contractor license, so there is nothing to transfer. Here is North Carolina's standard path for out-of-state applicants.

Your origin state does not issue a statewide license at this level, so there is no license to transfer. The destination's standard out-of-state path is shown; expect to meet it in full.

Reference only, not legal advice. Rules change; confirm with the licensing board before you apply. Full disclaimer.

NASCLA Accredited Examination in place of the North Carolina Building Contractor examination

Your out-of-state credentials give no advantage. You meet the destination's requirements from scratch.

North Carolina does not recognize an out-of-state general contractor license on its own, but it does accept the NASCLA Accredited Examination for Commercial General Building Contractors in place of its own Building Contractor trade examination. That route is open to anyone regardless of which state licensed them: sit the NASCLA examination before applying, then file the North Carolina application with the NASCLA pass letter and transcript purchase receipt attached and take the North Carolina Business and Law examination. Everything else still applies in full, including the financial responsibility figure for the limitation requested, the background check, character references and entity registration. An applicant who does not hold the NASCLA credential and comes from a state without a waiver agreement simply takes the North Carolina Building Contractor examination instead: 90 questions, 200 minutes, 70% to pass. North Carolina requires no trade experience for licensure, so out-of-state years do not shorten any step.

The Board confirms NASCLA acceptance on its own contractor FAQ and in 21 NCAC 12A .0303(c), which names the NASCLA examination alongside an origin state examination as the qualifying exam. The FAQ states acceptance for the Building classification; it does not say the NASCLA examination is accepted for the Residential classification. The NASCLA examination is bought and scheduled from NASCLA, not from the Board or PSI, and it is taken before the North Carolina application is filed. Without NASCLA and without a waiver agreement, substitute the North Carolina Building Contractor examination for the waived trade examination below; the Business and Law examination is then part of that classification examination rather than a separate sitting.

At a glance

Trade exam
Waived
Law / code exam
Required
Out-of-state hours
Do not count

What you must already have

  • You must have passed a licensing exam in New York that the destination considers comparable.NASCLA Accredited Examination for Commercial General Building Contractors, passed before the North Carolina application is filed. The Board asks for the NASCLA pass letter and the transcript purchase receipt to be attached to the application.
  • The qualifier is at least 18 years old and possesses good moral character as determined by the Board (G.S. 87-10). North Carolina sets no minimum trade experience or apprenticeship hours for a general contractor license.

What you'll do to get licensed in North Carolina

  1. 1Law / code exam. Pass a law, rules, or code exam. North Carolina Business and Law examination: 40 questions, 90 minutes, 70% to pass, covering erosion and sedimentation control, licensing, liens, contracts, project management, safety and business practices. Required of applicants who qualify on the NASCLA examination rather than the North Carolina Building Contractor examination..
  2. 2Trade exam. Pass the destination's trade exam (if applicable). Not required if the NASCLA Accredited Examination has been passed. Otherwise the North Carolina Building Contractor examination applies: 90 questions, 200 minutes, 70% to pass, open book, administered by PSI Services LLC after the Board issues an eligibility letter..
  3. 3Application fee. Pay the application fee ($75). Nonrefundable application fee set by the limitation requested: $75 for a limited license, $100 for an intermediate license and $125 for an unlimited license (G.S. 87-10(a1); 21 NCAC 12A .0304(a)). The amount shown is the limited-license fee..
  4. 4Exam fee. Pay the exam fee ($79). $79 per examination, paid to PSI Services LLC when the examination is scheduled. The NASCLA examination itself is bought from NASCLA and is not covered by this fee..
  5. 5Financial responsibility. Show financial responsibility of at least $17,000. Evidence of financial responsibility for the entity that will hold the license. Current assets must exceed current liabilities by at least $17,000 for a limited license (or total net worth of at least $80,000), $75,000 for an intermediate license, or $150,000 for an unlimited license. Intermediate and unlimited applicants must show the figure in an agreed-upon procedures report on the Board form or an audited financial statement prepared by a CPA or independent accountant. Statements must be no more than twelve months old and conform to GAAP (21 NCAC 12A .0204). The amount shown is the limited-license working capital figure..
  6. 6Surety bond. Post a surety bond ($175,000) (if applicable). Optional alternative to the working capital or net worth figure: a continuous surety bond of $175,000 for a limited license, $500,000 for an intermediate license or $1,000,000 for an unlimited license, from a surety authorized in North Carolina and rated Superior or Excellent by A.M. Best. Proof is filed with the application and with every annual renewal, and the bond must stay in force until the licensee can show the required working capital (21 NCAC 12A .0204(e))..
  7. 7Background check. Complete a background check. Criminal background check through the third-party vendor the Board names, paid directly to the vendor. Every qualifier submits to the check, along with the sole proprietor, the president of a corporation, all managers and members of an LLC, or all partners of a partnership (21 NCAC 12A .0303(b))..
  8. 8Business license. Obtain a business license. The license is issued to a legal entity, so the individual, corporation, LLC or partnership that will contract must be formed and, if organized outside North Carolina, authorized to transact business in the State before the license is issued (G.S. 87-10.1)..
  9. 9Insurance. Carry the required insurance (if applicable). The Board states there is no insurance or bonding requirement for a general contractor license itself. North Carolina workers compensation law still applies to the business independently of licensure, and owners, lenders and general contractors commonly require general liability coverage by contract..
  10. 10Continuing education. Complete continuing education. Renewal condition rather than an entry requirement: at least one qualifier on a building, residential or unclassified license must complete eight hours of Board-approved continuing education each year, made up of a two-hour mandatory course and six elective hours, with up to four elective hours carried forward (G.S. 87-10.2)..
  11. 11Other. Letters of character reference required by 21 NCAC 12A .0303(a)(9) and .0308, certified copies of court records for any criminal convictions of the applicant or its qualifiers, and disclosure of disciplinary history with this or any other licensing agency..

Published fees on this path total $154, excluding exam-vendor fees, bonds, and insurance.

What you'll need to buy or arrange

Exam preparation

Most boards contract PSI, Prov, or ICC for exams. Check which code edition the exam is written to before buying a prep course.

  • Law / code exam
  • Trade exam · if applicable
  • Exam fee · $79

Surety bond

A license or contractor bond is bought from a surety, not the state. Price is a small percentage of the bond amount and depends on your credit.

  • Surety bond · $175,000 · if applicable

Business registration

If you plan to contract in your own name, budget for a business license or entity registration on top of the trade license.

  • Business license

Liability insurance

Some states require proof of general liability or workers' compensation coverage at licensing time.

  • Insurance · if applicable

Continuing education

Renewals usually need approved CE hours, often on the latest NEC. Reciprocal licensees are rarely exempt.

  • Continuing education

How North Carolina licenses general contractors

North Carolina general contractor · “General Contractor, Building classification (Limited, Intermediate or Unlimited)

Statewide license

Verified September 17, 2026· 6 sources

Issued by North Carolina Licensing Board for General Contractors

The unlimited tier in North Carolina is the Building classification of the General Contractor license, issued by the North Carolina Licensing Board for General Contractors and required for any single undertaking costing $40,000 or more. The Building classification covers all building construction and demolition, commercial, industrial, institutional and residential alike, plus parking decks, site work and paving, storm drainage, retaining walls, recreational facilities and a list of specialty categories including concrete, masonry, roofing, metal erection, interior construction, swimming pools and asbestos. The Board also issues Highway, Public Utilities and Specialty classifications for work outside building construction, and separate North Carolina boards license the electrical, plumbing, heating and fire sprinkler trades. As with every classification, the license is held by a business and qualified by a named individual who passes the examination, and it carries a monetary limitation: Limited up to $750,000 per project, Intermediate up to $1,500,000, and Unlimited with no project cap, each set by the working capital, net worth or surety bond the applicant can show. North Carolina accepts the NASCLA Accredited Examination for this classification, and it holds examination waiver agreements with a short list of named states, but the Board states it does not have full reciprocity with any state.

Moving to North CarolinaLeaving North Carolina

Why New York has nothing to transfer

New York general contractor · “General Contractor Registration (NYC) / General Contractor and Light Commercial Contractor license (Buffalo)

Licensed by cities and counties

Verified September 17, 2026· 15 sources

Issued by New York City and city building departments (no statewide general or building contractor license)

New York has no statewide general, commercial, building or unlimited contractor license, and no state board examines or qualifies builders. The Department of State's Division of Licensing Services regulates 35 occupations and none of them is contractor; what the state does license around construction is narrow and specialized — home inspectors, manufactured housing, security and fire alarm installers through the Department of State, and asbestos contractors through the Department of Labor — while the individual building trades are licensed locally rather than by the state. Commercial and new-building work is controlled through the building permit, city by city. New York City requires a General Contractor Registration from the Department of Buildings before a contractor can pull New Building permits for one-, two- and three-family homes, and a registered Construction Superintendent at new buildings and demolitions nine stories and below; Buffalo issues graded General Contractor, New Housing, Light Commercial and Demolition licenses through a monthly advisory board. Most county home improvement laws stop short of this tier on purpose — Suffolk's and Westchester's both exclude new home construction — so outside the cities that license, a commercial builder in New York works under the permit and the Uniform Code with no contractor credential at all. A general contractor arriving from another state has nothing to transfer at state level and no reciprocity to apply for: the work is registering where registration is required and making sure the electrical, plumbing and fire-protection scopes are performed by people holding the right local trade licenses.

How local licensing works in New York

How it works in New York. No New York agency issues a general, commercial, building or unlimited contractor license. There is no state qualifying party, no business-and-law exam, no financial statement filed with a state board and no NASCLA route, because there is no board to file with. That means an out-of-state general contractor's license, its classification and any NASCLA Accredited Examination score carry no weight at state level. What decides whether you can work is the jurisdiction: a registration in New York City, a graded license in Buffalo, a county home improvement license where the job is a renovation rather than a new building, and the correct local trade licenses for the subcontracted scopes everywhere.

New York City — General Contractor Registration. The Department of Buildings requires that "all contractors who build one-, two-, and three-family homes must register with the Department to obtain New Building permits." Registration is $300, renewal $240, late renewal $50, and the term is three years. The applicant must "be at least eighteen (18) years old", "be able to read and write the English language", show good moral character, pass a background investigation and prove financial solvency — the last of which means a company bank account with "a minimum end balance of at least $25,000 for the past three (3) months", evidenced by three consecutive statements. Insurance is general liability with a $1 million minimum, plus workers' compensation and disability certificates. The filing is a notarized LIC6 form with EIN documentation, government photo ID, a Child Support Certification Form and proof of business address, submitted through DOB NOW; paper applications have not been accepted since September 7, 2021. There is no exam and no published experience minimum.

New York City — larger and commercial work. For buildings above the one-to-three-family tier, New York City does not license the general contractor at all; it regulates the site. "A registered Construction Superintendent is required at new buildings and buildings under demolition nine stories and below" — registration $100, renewal $50, term three years, applied for in DOB NOW after a DOB-approved training course. Bigger jobs are governed by site safety requirements and by DOB's other licenses and registrations: electricians, master and journeyman plumbers and fire suppression piping contractors, riggers, sign hangers, hoisting machine operators, welders, concrete safety managers and concrete testing laboratories, site safety professionals and special inspection agencies. Qualifications for all of them are in Chapter 4 of the 2022 NYC Administrative Code. Separately, any work on residential property in the five boroughs still needs the DCWP Home Improvement Contractor license — see the residential level, because in practice most contractors working in New York City need that one first.

Buffalo. Buffalo is the New York city that most closely resembles a classic graded contractor license. Under Chapter 144 of the City Ordinances, anyone "doing construction work in the City of Buffalo" needs a city Contractor License, which "does not allow for plumbing, heating, cooling or electrical work", and working without one is an unclassified misdemeanor carrying up to $1,000 or 60 days. At this tier the categories are General Contractor — "Companies with extensive experience in major construction work will qualify. To perform construction of new residential and commercial structures without limitations", including infrastructure — New Housing Contractor (new residential and commercial structures up to three stories plus remodeling, excluding infrastructure), Light Commercial Contractor (repairs, remodeling, alterations, conversions and modernization of commercial property, plus additions and new accessory structures up to three stories), Construction Manager (oversight and scheduling only, cannot perform construction work) and Demolition Grades 1 through 4. Minimum general liability aggregates are $2,000,000 for General Contractor and every demolition grade, $500,000 for Light Commercial, Specialty, Subcontractor and New Housing, and $50,000 for Handyman and Construction Manager, with the Office of Licenses at 301 City Hall as certificate holder and no PO Box addresses accepted. Demolition Grades 2 and 3 need reference letters from two townships where demolition work was performed, waivable with a resume showing ten years of demolition experience; Grade 4 needs a New York State explosives license held by a major corporate officer. New Housing applicants file copies of the warranties given to new home buyers. Asbestos abatement requires the firm's New York State Department of Labor Asbestos License, lead abatement requires EPA firm certification, and fire suppression system installation requires approval from the Chief of Fire Prevention. Applications must arrive at least seven days before the monthly Construction & Home Improvement Advisory Board meeting, and "attendance at the meeting is mandatory for the applicant" unless a notarized letter authorizes a representative. The fee is not printed on the application packet; ask the Office of Licenses on (716) 851-6583.

The counties stop below this tier. Nassau, Suffolk, Westchester, Rockland and Putnam license home improvement, not building. Suffolk's Chapter 563 definition expressly excludes "the construction of a new home", and the Westchester law states that it "shall not apply to ... the construction of a new home building", along with plumbing work, electrical work and architectural services. A builder putting up new houses in those counties may therefore need no county license at all, while the same builder's remodeling arm does — and both still answer to the town or village building department. Check the scope with the county before assuming either way.

Yonkers and Rochester. Yonkers licenses home improvement contractors who "renovate existing dwellings of 1 to 3 families" and does not issue a commercial builder license; new and commercial construction is handled through the Department of Housing and Buildings permit process. Rochester licenses only electricians, plumbers and stationary engineers / refrigeration operators, and holds the permit applicant responsible for making sure "all required contractors are licensed, proof of insurance is filed and the project complies with the permit".

Everywhere else. Outside the jurisdictions above, commercial construction in New York is governed by the Uniform Code and the local building department, and in most towns and villages a general contractor needs no license — only permits, insurance and licensed trades. Confirm with the building department for the job site, and where the project involves residential property anywhere in the state, General Business Law Article 36-A's written-contract and deposit-escrow rules still apply.

Moving to New YorkLeaving New York

Common questions

Do I have to take the North Carolina general contractor exam if I'm licensed in New York?
The trade exam is waived, but North Carolina requires a law or code exam.
What does it cost to get a North Carolina general contractor license from New York?
Published fees on this path total $154, not counting exam vendor fees or bonds.
Do my New York work hours count in North Carolina?
No. North Carolina does not credit out-of-state hours on this path.
Does it work the other way, from North Carolina to New York?
Not necessarily. Reciprocity is directed. Going from North Carolina to New York, the mechanism is not applicable.

Sources

  1. NASCLA Accredited Examination for Commercial General Building Contractors · National Association of State Contractors Licensing Agencies · Other · verified September 17, 2026
  2. N.C.G.S. 87-10 - Application for license; examination; certificate; renewal · N.C.G.S. 87-10(a), (a1), (b), (c), (c1), (e) · North Carolina General Assembly · Statute · verified September 17, 2026
  3. N.C.G.S. 87-15.1 - Reciprocity of licensing · N.C.G.S. 87-15.1 · North Carolina General Assembly · Statute · verified September 17, 2026
  4. Classifications and limitations - NC Licensing Board for General Contractors · North Carolina Licensing Board for General Contractors · Agency Page · verified September 17, 2026
  5. FAQ for Contractors - NC Licensing Board for General Contractors · North Carolina Licensing Board for General Contractors · Faq · verified September 17, 2026
  6. Laws and Regulations Applicable to General Contracting in the State of North Carolina (2026 edition) · 21 NCAC 12A .0202, .0204, .0303, .0304, .0402, .0403, .0404 · North Carolina Licensing Board for General Contractors · Admin Rule · verified September 17, 2026
  7. License applicants - NC Licensing Board for General Contractors · North Carolina Licensing Board for General Contractors · Agency Page · verified September 17, 2026
  8. Licensure Application Questions - License Type Selector (online application preview) · North Carolina Licensing Board for General Contractors · Form · verified September 17, 2026
  9. State of North Carolina Licensing Board for General Contractors - Candidate Information Bulletin · PSI Services LLC for the North Carolina Licensing Board for General Contractors · Other · verified September 17, 2026

Verified dates are when a person last opened each source and confirmed the facts above. Cite the board, not us.

Report an error on this page

Related