Illinois to Alabama: residential contractor license reciprocity
Illinois does not issue a statewide residential contractor license, so there is nothing to transfer. Here is Alabama's standard path for out-of-state applicants.
Your origin state does not issue a statewide license at this level, so there is no license to transfer. The destination's standard out-of-state path is shown; expect to meet it in full.
Reference only, not legal advice. Rules change; confirm with the licensing board before you apply. Full disclaimer.
Unlimited Home Builders License by examination (states with no exemption on the Board's list)
Your out-of-state credentials give no advantage. You meet the destination's requirements from scratch.
A residential builder arriving from a state that is not on the Board's short exemption list gets no credit for the license held elsewhere. The applicant entity files the notarized application, names its designated qualifying representative, pays the $100 processing fee and the $250 annual license and Recovery Fund fees in one $350 payment, orders a business-related credit report sent straight to the Board by the credit agency, files the entity certificates and proves citizenship or lawful presence. The qualifying representative then takes both Alabama Home Builders exams through Prov: the Skill exam (80 questions, four hours, 66% to pass, based on the 2015 International Residential Code) and the Business and Law exam (40 questions, two hours, 70% to pass). No Board authorization is needed to book the exams and a passing score stays good for three years. Alabama sets no minimum years of building experience, so documented out-of-state work neither shortens nor replaces any step. The Board says a complete file takes roughly three to four weeks and must be complete seven days before the Board meeting that reviews it.
Both Prov examinations are required on this path, and the Business and Law exam is never waived at any level. A license with limitation or limited to roofing skips the examination entirely, but its experience test is a business or occupational license as a contractor issued by an Alabama municipality, township or county, currently held or held within the year before the application, so an out-of-state local license does not open that route; the alternatives are a written recommendation from the holder of an unlimited home builders license in Alabama or any other state, or from a building official in Alabama or any other state. Licenses run for the calendar year and renew by November 30 for the following year, with six hours of continuing education. A general contractor license issued by the other Alabama board does not cover residential construction unless its number is below 18908, which means issued before the Home Builders Licensure Board was created in 1992.
At a glance
- Trade exam
- Required
- Law / code exam
- Required
- Out-of-state hours
- Do not count
- Typical processing
- About 28 days
What you must already have
- The Board must be satisfied that the applicant has the experience, ability, good character and willingness to serve the public required by Ala. Code § 34-14A-5. There is no published minimum number of years or hours of residential building experience for an unlimited license.
What you'll do to get licensed in Alabama
- 1Trade exam. Pass the destination's trade exam. Alabama HBLB Skill Exam through Prov: 80 questions, 4 hours, 66% to pass, open book against the 2015 International Residential Code and the Residential Home Builder Study Guide, covering plan reading, sitework and foundations, concrete, masonry, carpentry, roofing, interior and exterior finish, associated trades and OSHA. No Board authorization is needed before booking, and a passing score stays valid for three years..
- 2Law / code exam. Pass a law, rules, or code exam. Alabama HBLB Business and Law exam through Prov: 40 questions, 2 hours, 70% to pass, open book against the NASCLA Contractors Guide to Business, Law and Project Management, Alabama Residential Construction edition. This exam is never waived..
- 3Exam fee. Pay the exam fee ($130). $130 if the Skill and Business and Law exams are taken on the same day, or $80 for each exam taken on separate days. Testing fees are paid directly to Prov, not to the Board..
- 4Application fee. Pay the application fee ($100). Non-refundable new license application processing fee (Ala. Admin. Code r. 465-X-4-.04(3)). It is paid together with the annual license fee in a single payment and is not returned if the application is withdrawn or denied..
- 5License fee. Pay the license or certificate fee ($250). Annual license fee of $235 plus the $15 annual Homeowners' Recovery Fund fee, sent with the application as one $350 payment together with the $100 processing fee. The license fee is refunded on written request if the application is rejected or denied. A license limited to residential roofing costs $150 a year and pays no Recovery Fund fee. Cheque or money order only; the Board does not take cash or credit cards..
- 6Financial responsibility. Show financial responsibility. Business-related credit report including a public records search, ordered by the applicant at a fee of $35 and sent to the Board directly by the credit reporting agency. There is no net worth or working capital minimum, but outstanding business-related collection or foreclosure accounts must not exceed $500 in total, and outstanding judgments, judgment liens or perfected liens must not exceed $500 in total ($1,000 where the matter is under dispute or on appeal), unless the applicant documents payment, a payment plan or the circumstances to the Board's satisfaction. An application pending more than 90 days may need an updated report..
- 7Business license. Obtain a business license. The license is issued to the legal entity that will contract. A corporation, limited liability company or limited partnership files a Certificate of Compliance from the Alabama Department of Revenue, and an entity organized outside Alabama also files a Certificate of Existence from the Alabama Secretary of State. Conducting residential homebuilding through an entity that does not itself hold an Alabama Home Builders license is a violation of the Act..
- 8Surety bond. Post a surety bond ($10,000) (if applicable). Required only for a license limited to residential roofing: a surety bond of not less than $10,000 naming the Home Builders Licensure Board as obligee, valid through December 31 of the licensure year and submitted to the Board directly by the surety (Ala. Admin. Code r. 465-X-3-.04(5)). Roofers file this instead of a credit report. Unlimited and limited licenses require no bond..
- 9Insurance. Carry the required insurance (if applicable). The Board states that the law regulating residential home builders does not address insurance, so no policy is required for licensure. Other Alabama laws, and most lenders and homeowners, still expect general liability and workers compensation coverage; the Alabama Department of Labor answers questions about workers compensation..
- 10Continuing education. Complete continuing education. Renewal condition rather than an entry requirement: six credit hours of Board-approved continuing education each year, two of them in Alabama-specific subjects, taken by the designated qualifying representative where the license is held by an entity. Licenses run for the calendar year and renewal applications are due by November 30 of the preceding year (Ala. Admin. Code r. 465-X-3-.06)..
- 11Other. Notarised application on the Board's form (no photocopies), notarized corporate minutes or equivalent naming the designated qualifying representative as an officer, general partner, member or manager, and proof of United States citizenship or lawful presence for every applicant..
Published fees on this path total $480, excluding exam-vendor fees, bonds, and insurance.
What you'll need to buy or arrange
Exam preparation
Most boards contract PSI, Prov, or ICC for exams. Check which code edition the exam is written to before buying a prep course.
- Trade exam
- Law / code exam
- Exam fee · $130
Business registration
If you plan to contract in your own name, budget for a business license or entity registration on top of the trade license.
- Business license
Surety bond
A license or contractor bond is bought from a surety, not the state. Price is a small percentage of the bond amount and depends on your credit.
- Surety bond · $10,000 · if applicable
Liability insurance
Some states require proof of general liability or workers' compensation coverage at licensing time.
- Insurance · if applicable
Continuing education
Renewals usually need approved CE hours, often on the latest NEC. Reciprocal licensees are rarely exempt.
- Continuing education
How Alabama licenses residential contractors
Alabama residential contractor · “Residential Home Builders License (without limitation, with limitation, or limited to residential roofing)”
Statewide license
Issued by Alabama Home Builders Licensure Board
Alabama licenses residential builders statewide through the Home Builders Licensure Board in Montgomery, which is a different agency from the Alabama Licensing Board for General Contractors that handles commercial work. A license is required to construct, remodel, repair or improve a residential structure where the cost of the undertaking including labor and materials exceeds $10,000. There are three tiers: a license without limitation (unlimited), which covers whole houses, work involving more than one trade and residential roofing; a license with limitation (limited), for single-trade work that is not a whole residence; and a license limited to residential roofing. The license is held by the business, not the person: an individual may be licensed personally, but a partnership, corporation, LLC or non-profit must name a designated qualifying representative who is a general partner, officer, member or manager and who personally meets the experience and examination requirements, so an inbound builder applies as or for the entity that will sign contracts. An unlimited license is earned by passing the Alabama Home Builders Skill exam and the Business and Law exam through Prov and by showing business-related financial responsibility through a credit report; Alabama sets no minimum years of experience. The Board publishes one reciprocity rule, naming five states whose residential licensees may skip the Skill exam.
Why Illinois has nothing to transfer
Illinois residential contractor · “No statewide license; local titles include Chicago General Contractor Class D or E and Chicago Home Repair”
Licensed by cities and counties
Illinois issues no statewide residential contractor, home builder or remodeler license, and no state agency examines or qualifies people who build or remodel houses. What the State does license is narrower and worth knowing: the Department of Financial and Professional Regulation licenses roofing contractors under the Illinois Roofing Industry Licensing Act, where a limited license covers residential properties of eight units or less and an unlimited license covers residential, commercial and industrial roofs, and a municipality or county may not issue a building permit to a roofing contractor without proof of that state license. IDFPR also licenses architects, professional and structural engineers, land surveyors and alarm contractors, and the Department of Public Health licenses plumbers, plumbing contractors and irrigation contractors, but nowhere on IDFPR's list of regulated professions is there a general, residential or building contractor. Everything else is local: Illinois municipalities are home rule units and license or register residential contractors one jurisdiction at a time, with the City of Chicago's General Contractor license by far the most consequential. A builder moving to Illinois therefore has no state license to transfer and no reciprocity to apply for; the practical work is registering in each city or county where they will pull permits, carrying the insurance each one demands, and obtaining the state roofing license if the company will do roofing. Statewide consumer law still applies: the Home Repair and Remodeling Act requires a written contract for any home repair or remodeling job over $1,000 and the "Home Repair: Know Your Consumer Rights" pamphlet on every job.
How local licensing works in Illinois
How it works in Illinois. There is no state license, no state application and no state exam for residential contractors. Each municipality decides who may pull a residential building permit, so a contractor must be licensed or registered separately in every jurisdiction where they build, and a credential from one Illinois city is not valid in the next. Almost all of these local programs are about identity, insurance, bonding and fees rather than trade competence, and none of them reviews or credits a residential contractor license held in another state. Roofing is the exception in the other direction: the State license is mandatory everywhere in Illinois, and cities from Rockford to Joliet to Cook County check it at the permit counter.
Chicago. This is the license that matters. 'A City of Chicago general contractor license is required to perform most types of building construction, alteration, repair, and demolition work within the City of Chicago', and it is needed to bid on, undertake, hire or supervise, or control the means and methods of work requiring a building, sign or demolition permit. Licenses are issued to businesses, including sole proprietorships, in five classes set by project value - the fair market value of materials and labor supplied by all contractors and subcontractors across all concurrent and consecutive work at the same site. The two classes a homebuilder or remodeler usually needs are Class D, capped at $4 million with ordinary demolition and $2 million per occurrence of insurance, at a $900.00 license and renewal fee, and Class E, capped at $500,000 with no demolition and $1 million per occurrence, at $300.00. There is no exam, no experience review and no qualifying party. The application asks for a statement of financial solvency in the format supplied, proof of authority to do business in Illinois (not required for sole proprietors), an Assumed Name Certificate from the County Clerk if a trade name is used, proof of insurance for the class from an insurer authorized in Illinois and rated B+ or better by A.M. Best, and government photo identification for the controlling persons. Continental Testing Services processes the application and renewal by mail for the Department of Buildings; the license runs one year and 'is automatically inactivated if the associated insurance policy expires.' Reinstatement costs $100.00 per year or part year expired.
Chicago, work that does not need a permit. A business that fixes, replaces, alters, modernizes, improves or adds to residential property but does not need a building permit takes a Home Repair license from Business Affairs and Consumer Protection instead: $1,000.00 for a two-year term, with a certificate of insurance of at least $300,000 per occurrence, and the rule that 'Home Repair licensees may not pull building permits.' A general contractor license replaces it - 'a home repair license is not required for a business that holds a General Contractor license', though a general contractor doing residential work must still follow the home repair consumer protection rules, which include a written estimate before work, a written invoice on completion, prior approval before exceeding the estimate, and the license number on contracts, advertisements and vehicles. Acquiring vacant land to build a new home, or renovating more than half of an existing building's floor area, requires a separate Residential Real Estate Developer license.
Cook County (unincorporated areas). 'All contractors performing work in unincorporated Cook County are required to register with the Cook County Department of Building and Zoning.' Registration costs $150 per trade initially and $75 per trade annually, due by December 31, and needs a $1,000,000 general liability certificate naming Cook County Building and Zoning at 69 W. Washington, Suite 2830, Chicago as certificate holder, filed by the owner or a corporate officer with the Articles of Incorporation or the current Annual Domestic Report. Roofing registrants must submit the State of Illinois roofing license and demolition registrants an approved bond. There is no exam. Homeowners who live on the property get 'General' contractor registration free of charge. Use the county's CookViewer tool first to check whether a site is actually unincorporated. Contact [email protected] or 312-603-0512.
Aurora. The Division of Building and Permits registers a General contractor for a $200 fee. The packet is the Contractor Licensing Application, a certificate of insurance naming the City of Aurora as primary and non-contributory additional insured with $1,000,000 general aggregate and $500,000 per occurrence, workers' compensation in compliance with Illinois statute, and proof the business is registered with the Secretary of State or a county DBA certificate. There is no test for the General category - Aurora's municipal testing applies only to electrical and mechanical contractors, who may use ICC certifications or a license from an accepted testing municipality instead. Roofing registration is also $200 and requires the state license, and workers' compensation cannot be replaced by an employee affidavit for roofers. Outstanding or expired permits will block a renewal. Submit to [email protected]; 77 S Broadway, (630) 256-3130.
Evanston. 'All contractors performing work within City limits are required to register with the City, including but not limited to General Contractors, Electrical, Carpentry, Concrete, Excavation, Masonry, Landscaping, Fence, Roofing and Sign contractors.' General Contractor registration is $150 and trade registration $125, both renewable annually through the Citizen Portal. Insurance must be general liability of at least $300,000 per occurrence, bodily injury of at least $100,000 per occurrence, property damage of at least $100,000 per occurrence and workers' compensation at statutory minimums, with Evanston as certificate holder; sole proprietors and partnerships with no employees may file an affidavit in place of workers' compensation, and right-of-way work needs $1,000,000 per occurrence naming the city as additional insured. State-regulated contractors submit a copy of the state license. An owner-occupant of a single-unit residence may act as their own general contractor.
Joliet. 'All contractors performing work within the City of Joliet must have current registration on file prior to permit issuance. There are no forms or fees for registration, unless you are a Sign Erector or for HVAC Testing.' Registration is a certificate of insurance naming the City of Joliet as certificate holder, with minimum limits of $250,000 bodily injury per person, $500,000 bodily injury per occurrence and $250,000 property damage per occurrence, emailed to [email protected]. Roofing needs the Illinois State Roofer's License, plumbing the Illinois Plumbing Contractor Registration, irrigation the state irrigation license, siding a Vinyl Siding Installers certificate, and electrical and HVAC a license from one of the municipalities Joliet accepts. Electrical, plumbing and HVAC contractors also file a project-specific Letter of Intent, and all subcontractors must be listed on the permit application.
Rockford. 'General contractors are not required to be licensed.' Rockford requires a building permit for any structure over 120 square feet that is constructed, altered, enlarged, repaired or moved, and for all roofing work, and notes that 'roofing contractors are required to obtain a license from the State of Illinois Department of Professional Regulation.' Tent erectors and outdoor sign contractors need annual city licenses.
Springfield. The Building and Zoning Department's published list of applications contains electrical and mechanical contractor registrations and licenses and nothing else for contractors - there is no general contractor or home improvement registration. The city's building permit application collects the general contractor's name and address but asks for a license number only on the roofing line. Building and Zoning is at 300 South 7th Street, Room 304, (217) 789-2171.
Peoria. Peoria's Contractor Business Licenses cover only four activities - parking lot paving, sidewalk and driveway work, placing a dumpster or storage unit in the right-of-way, and sewer connections - at $25.00 or $60.00 a year with license and permit bonds of $5,000 or $10,000. Its trade licenses cover electrical and HVAC contractors at $150.00 each, issued to individuals rather than businesses and requiring an open-book ICC exam unless the applicant holds a Normal or Pekin license, plus boiler tender and stationary engineer licenses. There is no general building contractor or residential builder license in Peoria.
Everywhere else. Other Illinois municipalities set their own rules and most of them register rather than license residential builders. Ask the building or development services department of each city, village or county before contracting there, and confirm the current fee and insurance limits before buying coverage, because these are set locally and change independently.
- Chicago (Department of Buildings - General Contractor license, Classes A-E)
- Chicago (Business Affairs and Consumer Protection - Home Repair business license)
- Cook County (Department of Building and Zoning - contractor registration, unincorporated areas)
- Aurora (Division of Building and Permits - General contractor registration)
- Evanston (Building and Inspection Services - General Contractor registration)
- Joliet (Building and Inspectional Services - contractor registration, no fee)
- Rockford (Construction and Development Services - general contractors not licensed)
- Springfield (Building and Zoning Department - electrical and mechanical registrations only)
- Peoria (Contractor Business Licenses and Trade Licenses)
- Naperville (City of Naperville - Permits and Licenses)
Common questions
- Do I have to take the Alabama residential contractor exam if I'm licensed in Illinois?
- Yes. Alabama requires the trade exam on this path, plus a law or code exam.
- What does it cost to get a Alabama residential contractor license from Illinois?
- Published fees on this path total $480, not counting exam vendor fees or bonds.
- Do my Illinois work hours count in Alabama?
- No. Alabama does not credit out-of-state hours on this path.
- How long does the application take?
- The board's published or typical processing time is about 28 days.
- Does it work the other way, from Alabama to Illinois?
- Not necessarily. Reciprocity is directed. Going from Alabama to Illinois, the mechanism is not applicable.
Sources
- Alabama Home Builders Licensure Board - Frequently Asked Questions, Applicants (reciprocity, thresholds, timelines) · Alabama Home Builders Licensure Board · Faq · verified September 17, 2026
- Alabama Home Builders Licensure Board - How to Get Licensed (license types, exams, credit report, bond) · Alabama Home Builders Licensure Board · Agency Page · verified September 17, 2026
- Home Builders Licensure Law and Administrative Rules and Regulations (law effective October 1, 2025; rules effective November 14, 2025) · Ala. Code § 34-14A-1 et seq.; Ala. Admin. Code r. 465-X-3-.04, 465-X-3-.06, 465-X-4-.04 · Alabama Home Builders Licensure Board · Admin Rule · verified September 17, 2026
- New Unlimited License Application Packet, Corporate - Alabama Home Builders Licensure Board (with Prov Candidate Information Bulletin) · Ala. Code §§ 34-14A-7, 34-14A-14 · Alabama Home Builders Licensure Board · Form · verified September 17, 2026
Verified dates are when a person last opened each source and confirmed the facts above. Cite the board, not us.