New York to Oregon: residential contractor license reciprocity
New York does not issue a statewide residential contractor license, so there is nothing to transfer. Here is Oregon's standard path for out-of-state applicants.
Your origin state does not issue a statewide license at this level, so there is no license to transfer. The destination's standard out-of-state path is shown; expect to meet it in full.
Reference only, not legal advice. Rules change; confirm with the licensing board before you apply. Full disclaimer.
CCB application with the NASCLA examination in place of the pre-license training (every state)
Your out-of-state credentials give no advantage. You meet the destination's requirements from scratch.
Oregon runs no contractor reciprocity at all. OAR 812-006-0300(6) says in terms that there are no reciprocal agreements with other states or with organizations that test contractors, and nothing in ORS chapter 701 recognizes a license issued elsewhere, so a residential contractor license held in another state does not by itself waive or shorten any step here. What the Board does accept is the NASCLA Accredited Examination for Commercial General Building Contractors: under OAR 812-006-0310 an RMI who has passed it satisfies the 16-hour pre-license training requirement outright, whenever the exam was taken, and only has to sit the Oregon contractor test, with the pass proved by the RMI's entry in the NASCLA National Examination Database. That rule sits in the division governing every RMI and is not limited to a commercial endorsement, so it is available to an applicant taking the Residential General Contractor endorsement. An RMI without the NASCLA credential simply takes 16 hours of training from a CCB-approved provider first and then the same Oregon test. There is no trade or classification examination in Oregon at all: the only test is the Oregon contractor test on laws, rules and business practices, 80 scored questions in 180 minutes with 70 percent to pass, open book against the NASCLA Contractors Guide to Business, Law and Project Management for Oregon, and it is never waived. Everything after that is the same for an applicant from any state: registration with the Oregon Secretary of State, a $25,000 residential bond and at least $500,000 per occurrence of liability insurance filed on the Board's own forms, workers' compensation cover if the business has employees, and the $400 application fee.
Oregon requires no trade experience for a residential endorsement, so documented out-of-state years neither shorten nor replace any step at this level. Two other routes to RMI status exist but rarely help an inbound contractor: continuous association with an Oregon-licensed business from before 1 July 2000 with no lapse over 24 months, and a sole proprietor exemption under Oregon Laws 2018 chapter 46. Separately, OAR 812-003-0265 gives the spouse of an active-duty servicemember stationed in Oregon a temporary authorization of up to two years on a current out-of-state general, commercial or residential contractor license in good standing, proving competency by the NASCLA examination, the Oregon examination, or eight years of licensed contracting in another state, plus three hours of Board education and the usual fee, bond and insurance. The Board publishes no fee for the 16-hour pre-license training because each approved provider sets its own price; the provider list and the licensing call center on 503-378-4621 are where to ask. The license must be applied for within two years of passing the Oregon test.
At a glance
- Trade exam
- Waived
- Law / code exam
- Required
- Out-of-state hours
- Do not count
- Typical processing
- About 42 days
What you must already have
- You must have passed a licensing exam in New York that the destination considers comparable.OAR 812-006-0310 accepts the pass whenever it was earned and proves it by the RMI's name appearing in the NASCLA National Examination Database, so no transcript is sent by the candidate. The NASCLA examination is an exam credential rather than a license or an interstate agreement, so it is open to a candidate from any state and gives no advantage tied to where the applicant is licensed now. It does not waive the Oregon contractor test, the bond, the insurance, the fee or any other requirement. An applicant without it takes 16 hours of approved training instead.
- The business must designate at least one Responsible Managing Individual: an owner or an employee who exercises management or supervisory authority over the construction activities of the business. An RMI who is not an owner may serve only one licensee at a time, and a business that loses its RMI must appoint a replacement immediately or a temporary RMI for no more than 14 days, or the license is suspended.
- You must have no disciplinary action or unresolved complaints on your record.ORS 701.098(1)(d). The application also requires five years of construction-related court judgments, administrative orders, pending complaints, convictions and indictments from any state, and unpaid construction debt blocks a new license for the business owners and for the RMI until it is satisfied.
What you'll do to get licensed in Oregon
- 1Other. At least 16 hours of pre-license training on business practices and law from a CCB-approved education provider, taken by the RMI. It is required of every applicant except an RMI who has passed the NASCLA Accredited Examination for Commercial General Building Contractors, and except the two narrow RMI routes based on pre-2000 Oregon licensure or the sole proprietor exemption. Providers set their own prices, so the Board publishes no figure; the approved provider list is on the CCB site and the education team can be reached on 503-934-2227. (if applicable).
- 2Law / code exam. Pass a law, rules, or code exam. The Oregon contractor test, administered by PSI at test centers in Oregon and other states or by remote proctor: 80 scored questions in 180 minutes, plus 8 unscored questions and 20 minutes, with 70 percent needed to pass. It is open book against the NASCLA Contractors Guide to Business, Law and Project Management for Oregon Construction Contractors, 2nd edition, which may be highlighted, tabbed and annotated beforehand. The subjects are Oregon contractor laws and regulations, business structure, employees, subcontractors, contracts, lien law, bidding and estimating, project management, building codes, jobsite safety, environmental factors, exterior shell, financial management and tax basics. A failed test may be retaken without limit, though not the same version on consecutive attempts, and the license application must follow within two years of the pass..
- 3Exam fee. Pay the exam fee ($60). PSI examination fee, payable when the test is scheduled. It covers first-time and repeat takers and stays valid for one year from the date of payment..
- 4Application fee. Pay the application fee ($400). CCB license application fee for a new license, set at $400 for applications received from 1 July 2025. It covers the two-year license; renewal is a further $400 every two years, and changing or adding an endorsement later costs $20. Application fees are not refunded. A licensee who is a sole proprietor or general partner on active duty in the armed forces does not pay a renewal fee falling due during that service..
- 5Surety bond. Post a surety bond ($25,000). A $25,000 residential surety bond for the Residential General Contractor endorsement, filed with the application. The Board accepts only its own CCB Residential Surety Bond form signed by an authorized agent of the surety or an attorney-in-fact, bearing a bond number, and filed within 60 days of the date the surety executed it. A residential bond answers only for residential and small commercial work, so a contractor also taking a commercial endorsement posts a second, commercial bond. Other residential endorsements carry different figures: $20,000 for Residential Specialty and $15,000 for Residential Limited and the restricted residential endorsements..
- 6Insurance. Carry the required insurance ($500,000). General liability insurance of at least $500,000 per occurrence for the Residential General Contractor endorsement, covering products and completed operations, with the certificate naming Construction Contractors Board, PO Box 14140, Salem, OR 97309 as certificate holder. Proof is filed with the application and again at every renewal. Residential Specialty needs $300,000 and Residential Limited $100,000. A contractor holding both a residential and a commercial endorsement carries a single policy at the higher of the two amounts..
- 7Insurance. Carry the required insurance (if applicable). Workers' compensation coverage, required of any business that is non-exempt, meaning it has employees. A sole proprietor with no employees, and a business in which every owner, officer or member is a family member, may file as exempt; the Board defines family as parents, spouses, sisters, brothers, daughters, sons, daughters-in-law, sons-in-law and grandchildren. A non-exempt applicant supplies its carrier, policy number, Workers' Compensation Division compliance number and employer tax identification numbers, and any change between exempt and non-exempt status must be reported to the Board within 10 days..
- 8Business license. Obtain a business license. A business entity that is required to register with the Oregon Secretary of State's Corporation Division must be registered, active and in good standing before the license issues, and every assumed business name used by the applicant must be registered as that entity's assumed business name. An out-of-state entity registers in Oregon in the same way..
- 9Background check. Complete a background check. The RMI clears a background check after the application is filed. The application itself asks the business and its owners and officers to disclose, for the five years before the application and from any state, unsatisfied construction-related court judgments and administrative orders, pending complaints alleging money owed, and judgments of conviction or indictments for the crimes listed in ORS 701.098, along with unpaid workers' compensation penalties and unpaid employee wages. Unsatisfied construction debt keeps both the owners and the RMI from obtaining a new CCB license until it is paid..
- 10Continuing education. Complete continuing education (if applicable). Not required to obtain the license. Each two-year license period a residential contractor must have an owner, officer, RMI or employee complete at least eight hours of continuing education, being three hours on CCB laws, regulations and business practices plus five hours of other approved courses. A contractor who has not held an Oregon residential license at any point in the six years before the renewal date completes an additional eight hours, so a newly licensed arrival owes 16 hours before the first renewal. Contractors who also hold certain Oregon licenses, including architect, engineer, electrician and plumber, are exempt..
- 11Other. A contractor whose Oregon work will include boiler, electrical, elevator or plumbing installation also needs the matching Building Codes Division contractor license, and OAR 918-030-0015 requires an active CCB license before the division will issue or renew one. The CCB license comes first, and it does not replace the division license..
Published fees on this path total $460, excluding exam-vendor fees, bonds, and insurance.
What you'll need to buy or arrange
Exam preparation
Most boards contract PSI, Prov, or ICC for exams. Check which code edition the exam is written to before buying a prep course.
- Other · if applicable
- Law / code exam
- Exam fee · $60
Surety bond
A license or contractor bond is bought from a surety, not the state. Price is a small percentage of the bond amount and depends on your credit.
- Surety bond · $25,000
Liability insurance
Some states require proof of general liability or workers' compensation coverage at licensing time.
- Insurance · $500,000
- Insurance · if applicable
Business registration
If you plan to contract in your own name, budget for a business license or entity registration on top of the trade license.
- Business license
Continuing education
Renewals usually need approved CE hours, often on the latest NEC. Reciprocal licensees are rarely exempt.
- Continuing education · if applicable
How Oregon licenses residential contractors
Oregon residential contractor · “Construction contractor license with the Residential General Contractor (RGC) endorsement”
Statewide license
Issued by Oregon Construction Contractors Board (CCB)
Oregon licenses contractors statewide through the Construction Contractors Board, and under ORS 701.021 anyone who undertakes, offers to undertake or bids work as a contractor must hold a current CCB license and the endorsement that matches the work. The unusual part of Oregon's structure is that there is only one construction contractor license: what the applicant chooses is an endorsement, and the endorsement sets the bond and the insurance. The homes tier is the Residential General Contractor (RGC) endorsement, which allows an unlimited number of unrelated building trades on residential or small commercial structures and carries a $25,000 residential bond and general liability insurance of at least $500,000 per occurrence. Its narrower siblings are Residential Specialty ($20,000 bond, $300,000 insurance, one or two trades), Residential Limited ($15,000 and $100,000, for a business under $40,000 of gross sales a year and $5,000 a contract) and Residential Developer, and a license may carry one residential endorsement, one commercial endorsement, or one of each, in which case the contractor posts two bonds and carries one liability policy at the higher amount. The license is held by the business rather than by the person: a sole proprietor, partnership, LLC, corporation or trust applies, and it must at all times have at least one Responsible Managing Individual (RMI), an owner or employee who exercises management or supervisory authority over the construction activities and who has completed 16 hours of CCB-approved pre-license training and passed the Oregon contractor test. Oregon sets no net worth, working capital or financial statement test and no minimum trade experience for a residential endorsement, so a builder moving to Oregon applies as or for the business that will sign the contracts and names themselves as its RMI.
Why New York has nothing to transfer
New York residential contractor · “Home Improvement Contractor license (municipal; title and scope vary by jurisdiction)”
Licensed by cities and counties
New York issues no statewide residential contractor, home improvement contractor or home builder license. The Department of State's Division of Licensing Services regulates 35 occupations — real estate brokers and salespersons, appraisers, home inspectors, manufactured housing, security and fire alarm installers, cosmetology and the like — and contractor is not among them. The only statewide law that reaches a residential contractor is General Business Law Article 36-A, which governs home improvement contracts rather than licenses: it requires a signed written contract, requires customer deposits taken before substantial completion to be held in escrow or covered by a bond, and asks the contract to state the contractor's "license number, if applicable" — the words "if applicable" are there precisely because the license, where one exists, comes from a county or a city. New York is one of the most fragmented licensing states in the country. New York City licenses home improvement contractors through the Department of Consumer and Worker Protection; Nassau, Suffolk, Westchester, Rockland and Putnam counties each run their own program; and cities including Yonkers and Buffalo license on top of or instead of the county. These licenses are held by the business and qualified by a named owner, officer or principal, so the reader is applying for a company license in their own name as the responsible individual. An out-of-state residential contractor has no state license to transfer and no state reciprocity to apply for, but a license already held elsewhere is not worthless: several New York jurisdictions accept it as evidence of qualifying experience.
How local licensing works in New York
How it works in New York. There is no state license, no state application and no state exam for residential contractors. A contractor must be licensed in every jurisdiction where the work is performed, and the licenses are not interchangeable — a Nassau County license does not authorize work in Suffolk, and a Westchester County license does not by itself authorize work in Yonkers. Almost every program licenses the business and requires one named owner, officer, principal or member to stand behind it, so budget for one application per county or city rather than one per person. Nothing in these programs is a state-to-state agreement, and none of them waives anything because of a license held in another state.
New York City — the one that matters most. The Department of Consumer and Worker Protection (DCWP) Home Improvement Contractor license is the single most consequential residential credential in the state: "A person or business must have a Home Improvement Contractor license to do construction, repair, remodeling, or other home improvement work to any residential land or building in New York City", including basements, driveways, fences, garages, landscaping, patios and swimming pools. One person — the sole proprietor, a general partner, a corporate officer, principal, director, member, or a shareholder owning 10% or more of the stock — must pass the Home Improvement Exam: 30 questions, at least 21 correct to pass, booked with ExamBuilder and sat at test centers open 9:00 a.m. to 5:00 p.m. seven days a week across the city, within 60 days of filing. The exam is included in the application fee for up to two attempts, and $50 buys two more. The applicant must either enroll in the Home Improvement Business Trust Fund for $200 or post a $20,000 surety bond, and must file a workers' compensation certificate naming DCWP at 42 Broadway, New York, NY 10004, or a CE-200 exemption. The license runs two years and expires on February 28 of odd years, so the fee is pro-rated by filing date: $200 from 1 March to 31 August of an odd year, $150 from 1 September of an odd year to the end of February, $100 from 1 March to 31 August of an even year, and $50 or $250 from 1 September of an even year depending on the term chosen. There is no experience requirement and no requirement that the business already be in New York.
Nassau County. The Department of Consumer Affairs runs the most demanding program in the state and the one that most rewards an out-of-state license. One owner, officer or principal "must have at least 5 years of recent, relevant verifiable experience in the home improvement field", proved by "five years of W2's, 1099's, or a license in another municipality". A new two-year license is $650, plus a separate one-time $50 payment into the Restitution Fund, $110 for each additional location and $60 to replace a lost license; every applicant also submits to a one-time fingerprint-based background check costing about $90. Liability insurance must show bodily injury limits of $250,000/$500,000 and property damage of $100,000 with the department at 240 Old Country Road, Mineola as certificate holder. At least one principal needs EPA RRP lead-safety certification where lead paint may be disturbed; irrigation work needs a New York backflow tester certification; pool and spa work needs five years' experience plus a CBP, CST, CSP or CMS certification. Out-of-state businesses face an extra hurdle: "you must provide a Certificate of Authority to do business in NY State, have a NY State location, as well as an authorized contact person that has a NYS residence." A judgment and open-complaint search is run on every principal, and all subcontractors except plumbers and electricians must hold their own Nassau license. There is no written exam. (516) 571-2600.
Suffolk County. Licensing sits with the Department of Labor, Licensing and Consumer Affairs under Chapter 563 of the county code, and home improvement licenses are more than half of everything the county issues. "Home improvement contracting" is defined broadly — carpentry, fencing, driveways, flooring, HVAC ductwork, masonry, roofing, siding, pools and spas, waterproofing, landscaping and tree work — but it expressly excludes electrical and plumbing work and "the construction of a new home". The fee is a $200 application fee plus $200 per annum for the license itself, the term is two years, and each salesperson needs a $50-per-year identification card. The Director may require a surety bond "in an amount to be set by the Director, but in no event to exceed $100,000" and sets the liability insurance figure. There is no general trade exam, but pool and spa builders need an APSP Certified Building Professional certification plus two years' experience, pool and spa service contractors need a CST, CSP or CBP plus two years, and renewing pool contractors need six hours of continuing education. (631) 853-4600.
Westchester County. "Westchester law requires that home improvement contractors have a county license." The fee is $750 for the two-year term as of January 1, 2026, with $100 for expedited handling, $50 for late renewal, $10 per vehicle decal and $50 for a replacement certificate. Processing normally takes about 60 business days, or seven business days if expedited. The packet is documentary rather than examined: notarized application, proof of business name from wherever the company is based, liability insurance naming the department at 148 Martine Avenue, Room 407, White Plains as certificate holder, workers' compensation and disability certificates (or a CE-200), photo ID for every owner, officer, member, partner, manager and salesperson, and a notarized child support certification from sole proprietors and partners. The application asks directly whether the company is "licensed in any other jurisdiction" and for those license numbers. A bond or cash security of up to $50,000 may be required at the Director's discretion, at application or later. The county law does not apply to plumbing, electrical or architectural work, to work within a state-licensed occupation, or to "the construction of a new home building". The cover letter warns that "the CITY OF YONKERS has additional licensing requirements". (914) 995-2155.
Yonkers. Inside Westchester County, Yonkers licenses separately through its Consumer Protection Bureau, and a contractor renovating existing one- to three-family dwellings in the city needs both. The Yonkers Home Improvement License costs $400, is non-refundable, runs two years and is not transferable. The packet requires a notarized application signed by an owner, partner or officer, vehicle registrations with automobile insurance (bumper stickers are issued for three vehicles, $10 for each additional one, and at least one vehicle must be listed), a DMV driver's license or non-driver ID, a $500,000 general contractor liability certificate naming the Office of Licensing/Consumer Protection, a workers' compensation certificate or CE-200, proof of business name, a NYS Certificate of Authority if the company charges sales tax, and a completed Work History Form. A background check is run on both the applicant and the business. Vehicles must display the business name, address and phone in eight-inch permanent letters or on a 2x3 foot sign. 914-377-6808.
Rockland County. Chapter 286 of the Laws of Rockland County requires everyone performing home improvement work in the county to hold a county Home Improvement License, issued by the Department of Consumer Protection / Weights and Measures. Rockland is unusually explicit about out-of-jurisdiction applicants: its applications are grouped by qualification route, one for applicants relying on experience in the trade classification, one for applicants who have held a license in another jurisdiction for at least five years without complaints or violations, and one for applicants posting a surety bond for the classification. A Home Improvement Licensing Board of trade members reviews credentials and investigates complaints, contractors must carry liability, workers' compensation and disability insurance, and general contractors must use licensed and insured subcontractors. Confirm the current fee and classification list with the department before filing: 845-364-3901.
Putnam County. The Office of Consumer Affairs registers home improvement contractors for $300, covering a two-year registration, and requires a $25,000 license and permit bond written for a two-year period, with the registration's expiration set to match the bond term. Also required: a certified business, partnership or corporate filing document, an ACORD liability certificate naming Putnam County Consumer Affairs as certificate holder and Putnam County as additionally insured with the scope of work spelled out, a workers' compensation form or CE-200, a notarized child support form for non-corporations, current vehicle registrations, a photo of the owner or highest-ranking officer, a driver's license from the applicant's home state, and — again a break for someone arriving with credentials — "copies of CURRENT HOME IMPROVEMENT LICENSES - if held in other municipalities". Decals come with the registration, extras are $5 each. Landscaping and lawn care contractors add a Lawn Care Best Management Practices certificate. 845-808-1617 ext. 46024.
Buffalo. Chapter 144 of the City of Buffalo Ordinances requires anyone "engaged in a home improvement business (i.e. painting, siding, roofing) or doing construction work in the City of Buffalo" to hold a city Contractor License, which "does not allow for plumbing, heating, cooling or electrical work". Working without one is an unclassified misdemeanor carrying up to $1,000 or 60 days. Residential categories are Handyman Contractor (minor repairs and maintenance, one named person, no roofing, siding or large renovations), Specialty Contractor, Sub-Contractor (cannot pull permits and must work under a prime) and New Housing Contractor. Minimum general liability aggregates are $50,000 for Handyman and Construction Manager, $500,000 for Light Commercial, Specialty, Subcontractor and New Housing, and $2,000,000 for General Contractor and every demolition grade. Applicants also file workers' compensation proof (C105.2, U-26.3, SI-12 or GSI-105.2) or a CE-200 that bars using subcontractors, register the business name with the Erie County Clerk even if it is registered elsewhere, and supply RRP or EPA lead firm certification unless exempt. The step that surprises people: the application must arrive at least seven days before the monthly Construction & Home Improvement Advisory Board meeting and "attendance at the meeting is mandatory for the applicant", in person or through a notarized representative. Ask the Office of Licenses for the current fee, which is not printed on the application packet: (716) 851-6583.
Rochester. Rochester licenses electricians, plumbers and stationary engineers / refrigeration operators and nothing else — there is no city home improvement or builder license. The city puts the duty on whoever pulls the permit: it is "the applicant's responsibility to ensure all required contractors are licensed, proof of insurance is filed and the project complies with the permit". Building Permit Office 585-428-6526.
Everywhere else. Outside these jurisdictions, hundreds of New York towns and villages regulate residential work only through the building permit and the state's Uniform Code, while others have their own contractor registration ordinances. Before signing anything, ask the county consumer affairs office and the town or village building department that covers the job site, and remember that General Business Law Article 36-A's written-contract and escrow rules apply everywhere in the state whether or not a license is required.
- New York City (Department of Consumer and Worker Protection — Home Improvement Contractor license)
- Nassau County (Department of Consumer Affairs — Home Improvement License)
- Suffolk County (Department of Labor, Licensing and Consumer Affairs — Home Improvement Contractor license)
- Westchester County (Department of Consumer Protection — Home Improvement License)
- Rockland County (Consumer Protection / Weights and Measures — Home Improvement License, Chapter 286)
- Putnam County (Office of Consumer Affairs — Home Improvement Contractor Registration)
- Yonkers (Consumer Protection Bureau — Home Improvement License, required in addition to the Westchester County license)
- Buffalo (Office of Licenses — Handyman, Specialty, Sub-Contractor and New Housing Contractor licenses)
- Rochester (Licensed Trades — electrical, plumbing and SE/RO only; no home improvement license)
Common questions
- Do I have to take the Oregon residential contractor exam if I'm licensed in New York?
- The trade exam is waived, but Oregon requires a law or code exam.
- What does it cost to get a Oregon residential contractor license from New York?
- Published fees on this path total $460, not counting exam vendor fees or bonds.
- Do my New York work hours count in Oregon?
- No. Oregon does not credit out-of-state hours on this path.
- How long does the application take?
- The board's published or typical processing time is about 42 days.
- Does it work the other way, from Oregon to New York?
- Not necessarily. Reciprocity is directed. Going from Oregon to New York, the mechanism is not applicable.
Sources
- NASCLA Accredited Examination for Commercial General Building Contractors · National Association of State Contractors Licensing Agencies · Other · verified September 17, 2026
- CCB Frequently Asked Questions (application), updated 3/2026 · Oregon Construction Contractors Board · Faq · verified September 17, 2026
- Construction Contractors Board - Continuing education · Oregon Construction Contractors Board · Agency Page · verified September 17, 2026
- CCB License Endorsements chart (11/2024) · Oregon Construction Contractors Board · Other · verified September 17, 2026
- Oregon Construction Contractors Board Examination Candidate Information Bulletin (PSI) · Oregon Construction Contractors Board / PSI Services LLC · Other · verified September 17, 2026
- Construction Contractors Board - How to get a CCB license (9 steps) · Oregon Construction Contractors Board · Agency Page · verified September 17, 2026
- CCB Sole Proprietorship License Application · Oregon Construction Contractors Board · Form · verified September 17, 2026
- Construction Contractors Board - Licensing (bonds, insurance, public works bond) · Oregon Construction Contractors Board · Agency Page · verified September 17, 2026
- OAR chapter 812, division 3 - Construction Contractors Board licensing · OAR 812-003-0131, 812-003-0142, 812-003-0152, 812-003-0153, 812-003-0260, 812-003-0265, 812-003-0270 · Oregon Secretary of State · Admin Rule · verified September 17, 2026
- OAR chapter 812, division 6 - Responsible Managing Individual, pre-licensure training, and testing · OAR 812-006-0100, 812-006-0110, 812-006-0150, 812-006-0160, 812-006-0300, 812-006-0310, 812-006-0450 · Oregon Secretary of State · Admin Rule · verified September 17, 2026
- OAR chapter 812, division 22 - Continuing education for residential contractors · OAR 812-022-0010, 812-022-0020 · Oregon Secretary of State · Admin Rule · verified September 17, 2026
- OAR 918-030-0015 - Contractor licenses (Building Codes Division requires a CCB license) · OAR 918-030-0015 · Oregon Secretary of State · Admin Rule · verified September 17, 2026
- ORS chapter 701 - Construction Contractors and Contracts (2025 edition) · ORS 701.005(16)-(17), 701.021, 701.042, 701.046, 701.050, 701.056, 701.063, 701.068, 701.073, 701.081, 701.084, 701.091, 701.098, 701.122 · Oregon Legislature · Statute · verified September 17, 2026
Verified dates are when a person last opened each source and confirmed the facts above. Cite the board, not us.